A hollow circular shaft with OD 1.5 and ID 1.25 and made of steel with an allowable shear stress of 15 ksi is rated for 5000 in-lbs of torque. A narrow slit is cut lengthwise along the shaft as shown in the figure on the right. Determine the rated capacity of the shaft after it has been modified. Choose the answer that is closest from the list below. 000 0 3,600 in lbs 360 in-lbs 1,800 in-lbs 2,500 in-lbs

A hollow circular shaft with OD 1.5 and ID 1.25 and made of steel with an allowable shear stress of 15 ksi is rated for 5000 in-lbs of torque. A narrow slit is cut lengthwise along the shaft as shown in the figure on the right. Determine the rated capacity of the shaft after it has been modified. Choose the answer that is closest from the list below. 000 0 3,600 in lbs 360 in-lbs 1,800 in-lbs 2,500 in-lbs

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
A 1.5-inch Monel shaft is used in a torsional application. Based on the operating speed of 100 rpm and factor of safety of 12. How much horsepower can it transmit? Assume the shearing stress is ¾ of the ultimate tensile stress which is 100 ksi.
A hollow circular shaft with the ratio of internal and external diameters of 0.6 is required to transmit 870 kW at 120 rpm, the maximum torque being 20% greater than the mean. Determine the dimensions of the shaft if the maximum shearing stress and twist in a length of 3m are limited to 60Mpa and 1.4°respectively. The G= 80Gpa.
a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
A shaft made of steel receives 7.5 kW power at 1500 rpm. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows: Ft = 1590 N; Fr=580 N Designe the shaft diameter by maximum shear stress theory. The shaft material has the following properties: Ultimate tensile strength = 720 MPa: Yield strength = 380 MPa: Factor of safety = 1.5