The thin-walled tube is subjected to an axial force of 40 kN If the tube contractes 3 mm and its circumference increases 0.09 mm, determine the modulus of elasticity, Poisson ratio, and the modulus of rigidity of the tube's material. Assume that the material does not yield.

The thin-walled tube is subjected to an axial force of 40 kN If the tube contractes 3 mm and its circumference increases 0.09 mm, determine the modulus of elasticity, Poisson ratio, and the modulus of rigidity of the tube's material. Assume that the material does not yield.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 3–26. The thin-walled tube is subjected to an axial force of 40 kN. If the tube elongates 3 mm and…

A: Given , F = 40 kN= 40x103N Initial length , lo=900 mm Change in length , l=…

Q: Find the young modulus of the rod of diameter 50 mm and of length 400 mm which is subjected to…

A: Given data:

Q: Determine the ratio of the shear modulus to the modulus of elasticity of material if the Poisson's…

A: G/E = 0.4

Q: a. Determine the torque T and the radius of the elastic-plastic boundary. b. Determine the residual…

A: The diameter f the solid shaft is D=100 mm. The elastic shear strength is τY=150 Mpa. The shear…

Q: The car bumper is made of polycarbonate-polybutylene terephthalate. If E = 2.0 GPa, determine the…

A: Given data: Young’s modulus, E = 2GPa Moment of inertia, I = 300 X 106 mm4 Springs stiffness, ksp =…

Q: Determine the equations of the elastic curve for the shaft using the x1 and x2 coordinates. Take El…

Q: F8-14. A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force…

A: Given data as per question length of rod = 600 mm Diameter of shaft =20mm Final diameter =…

Q: diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner…

Q: Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the…

A: Answer: The average shear strain in nylon due to load P is 0.1974 rad ( 11.3099°).

Q: A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is…

A: Given data: Width of the block = 20 mm Modulus of rigidity of the block, G = 26 GPa

Q: The rigid lever arm is supported by two A-36 steel wires having the same diameter of 4 mm. If a…

Q: The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is…

A: GIVEN: Load W= 30KN length of road BC:LBC=0.2m length of road CD:LCD=0.3m thickness of plate C: t=…

Q: The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The…

Q: 4. The shear stress-strain diagram for screws used in plating is the standard technique for treating…

Q: F8-12. If the elongation of wire BC is 0.2 mm after the force Pis applied, determine the magnitude…

A: elongation of wire BC 8= 0.2 mmd= 3 mm , l= 300 mm→ For A-36 steel , E= 200 GPa σy= 250 MPa

Q: The rod is 200 mm long and 60 mm in diameter. If an axial load of 300 N is applied to it, determine…

A: Given data:

Q: The specimen represents a filament-reinforced matrix system made from plastic (matrix) and glass…

A: The deformation of the matrix under the load P will remain the same. Therefore,

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

A: Given data: Normal stress in y direction, σy = - 15 ksi Normal stress in x direction, σx = 0 Shear…

Q: The car bumper is made of polycarbonate-polybutylene terephthalate. If E = 2.0 GPa, determine the…

A: Given data: Modulus of elasticity, E = 2 GPa. The velocity of the car, v = 0.75 m/s. The mass of…

Q: 1- Determine the total deformation of the suspended homogenous cone of height "h", density "p", and…

A: Given - Length of conical bar =h Radius of conical bar =r =d/2 Determine the elongation due to self…

Q: The A-36 steel bar consists of two segments, one ofcircular cross section of radius r, and one of…

A: The strain energy stored in circular section,

Q: A column of intermediate length buckles when the compressive stress is 40 ksi. If the slenderness…

A: Given data: The compressive strength of the column, σcr = 40 ksi. The slenderness ratio of the…

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD. If the wire has a diameter of…

A: Free-body diagram of the rigid pipe is given as, On using equilibrium of moment about A,…

Q: F8-15. A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force Pis…

A: Given data w=10 mmG=26 GPa

Q: The ball is truncated at its ends and is used to support the bearing load P. The modulus of…

Q: The bolt has a diameter of 10 mm, and the arm AB has a rectangular cross section that is 12 mm wide…

A: Diameter of bolt, d=10 mm,Cross section of rectangular plate, A=12 mm× 7 mmTension in the bolt,…

Q: 14-123. Two strain gauges a and b are attached to the surface of the plate which is subjected to the…

A: Given Data: The distributed load intensity in x-direction is wx = 700 kN/m. The distributed load…

Q: The assembly consists of a 30mm diameter aluminum bar ABC with fixed collar at B and a 10mm diameter…

A: Diameter of aluminum bar = 30 mm Modulus of elasticity of steel = 200Gpa Modulus of elasticity of…

Q: The beam is made of an elastic perfectly plastic material for which sY = 250 MPa. Determine the…

A: Given data: σy=250 MPa Determine the residual stresses in the beam at its top and bottom The stress…

Q: Determine the maximum force P and the corre- sponding maximum total strain energy that can be stored…

Q: The rigid bar is supported by the two short white spruce wooden posts and a spring. If each of the…

Q: The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an…

Q: R8-6. The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping…

A: Given Data: Clamping force on bolt is F = 4 kN. Modulus of elasticity is Est = 200 GPa. Yield…

Q: The slope of the stress-strain curve in the elastic deformation region is called Select one: O a.…

A: Slope of the stress-strain curve in the elastic deformation region is called modulus of elasticity.

Q: The pipe with two rigid caps attached to its ends is subjected to an axial force P. If the pipe is…

A: Total volume V=AL+πr2LδV=AδL+πr2δL=AξlongL+2πrξlatLr Poison ratio…

Q: The rigid lever arm is supported by two A-36 steel wires having the same diameter of 4 mm. If a…

A: Given data: A rigid lever supported by A-36 steel wires Diameter of wire (d) = 4 mm = 0.004 m…

Q: Determine the strain in the cables and the bar for the framing system where there are two rigid…

Q: a) In the composite spring shown, Spring 1 has a mean coil diameter of 36 mm and a wire diameter of…

Q: Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and…

Q: 4. Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while…

A: Given Data The width of the nylon strip is: w=5 mm The ditance from the edge is: 2 mm The force…

Q: E 600 mm B 400 mm 400 mm- - 400 mm-

Q: The rigid beam is supported by a pin at A and wires BD and CE. If the load P on the beam causes the…

Q: The below column (diameter 1 in.) is subjected to a compressive force where the diameter is…

Q: The steel link AB of the wire cutter has a dimensions of 3mmx 10mm, and modulus of elasticity of…

Q: The plexiglass bar has a stress–strain curve that can be approximated by the straight-line segments…

A: From the given stress-strain curve for Plexiglas bar: Failure point in Tension: σft=60 MPa and…

Q: The friction pad A is used to support the member, which is subjected to an axial force of P = 2 kN.…

Q: The head H is connected to the cylinder of a compressor using six 316-in. diameter steel bolts. If…

A: Given Data σy=40ksiEst=29000 ksi Find out the cross-sectional area A=πd24=π43162=0.027597 in2

Q: The link AB of the pliers has the cross section dimensions 3mm x 20mm, and is made of steel with…

A: Given: Modulus of elasticity of steel, E=190 GPa Dimension= 3mm * 20mm

Q: The modulus of elasticity for the steel cable is 25 (10)^6 psi. Determine the average stress in the…

A: Average stress is stress which produces due to pressure or forces which does not exceed the elastic…

Question

Need Solution through 15min

The thin-walled tube is subjected to an axial force of 40 kN
If the tube contractes 3 mm and its circumference increases
0.09 mm, determine the modulus of elasticity, Poisson ratio,
and the modulus of rigidity of the tube's material. Assume
that the material does not yield.
40 kN
900 mm
10 mm
40 kN
12.5 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The beam is made of phenolic, a structural plastic, that has the stress–strain curve shown. If a portion of the curve can be represented by the equation s = (5(106)P)1/2 MPa, determine the magnitude w of the distributed load that can be applied to the beam without causing the maximum strain in its fibers at the critical section to exceed Pmax = 0.005 mm>mm.
A bar has a length of 200 mm and cross-sectional area of 7500mm^2. Determine the modulus of elasticity of the material if it is subjected to an axial tensile load of 50 kN and stretches 0.075 mm. The material has linear-elastic behavior.
The deck of a bridge is made up of 12 mm thick steel plates 2 m long by 1·2 m wide. Under load, the plate is subject to tensile forces of 7·5 kN longitudinally and 6 kN across the width. Determine the change in the thickness of the plate under this load regime. Modulus of elasticity = 210 GN/m² and Poisson’s ratio = 0·3
Determine the ratio of the shear modulus to the modulus of elasticity of material if the Poisson's ratio is 0.25
The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy = 250 MPa. Determine the safety factor at point A using the maximum shear stress theory. Select one: a. NA = 1.843 b. NA = 3.224 c. NA = 2.580 d. NA = 4.299
A bar having a length of 5 in. and a cross-sectional area of 0.7 in.2 is subjected to an axial force of 8000 lb. If the bar stretches 0.002 in., determine the modulus of elasticity of the material. The material has linear elastic behavior.
The modulus of elasticity for the steel cable is 25 (10)^6 psi. Determine the average stress in the cable under the applied load. Assume a linear stress strain curve.
A plastic rod is 200mm long and 15mm in diameter. If a tensile load of 300N is applied to it, determine the change in its length and the change in its diameter. Assume Modulus of elasticity (E) = 2.70 GPa, and poisson's ratio (v) = 0.4. indicate free body diagram
A rubber bolt is inflated to apressure of 65kPa. At that pressure, tediameter of the ball is 240mm and the wall thickness is 1.25mm. The rubber has a modulus of Elasticity = 3.7 MPa and Poisson’s ratio v=0.48. Determine the maximum stress in the ball if its stress is half that of the cylinder
The rigid lever arm is supported by two A-36 steel wires having the same diameter of 4 mm. If a force of P = 3 kN is applied to the handle, determine the force developed in both wires and their corresponding elongations. Consider A-36 steel as an elastic perfectly plastic material.
The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 0.02R mm and an outer diameter of 0.444R mm. When the vessel is pressurized to 0.004R MPa, determine the change in the overall length of the vessel. Use E = 200 GPa and µ = 0.3 for steel. Neglect localized bending. Note R=993
The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 x 10-³. If Esteet = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.