3.a) In the composite spring shown, Spring 1 has a mean coil diameter of 36 mmand a wire diameter of 3mm. Determine the wire diameter of spring 2 if it hasa mean coil diameter of 24mm and the maximum shear stress in the two springsis to be the same.20.25NBSpring 2Spring 1b) If G=80 GPa and points A and B moved through 14mm and 19,94mmrespectively determine:i. the number of coils in each springii. the effective stiffness of the composite spring

Answered: Image /qna-images/answer/b7957b46-5f92-46bb-9a09-6d0d1b20e199.jpg

Answered: a) In the composite spring shown,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
Internal loadings at a critical section along a steel drive shaft are given. If the yield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B
Internal loadings at a critical section along a steel drive shaft are given. If theyield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B. （DON'T COPY OTHER ANSWER) AND 30mm is radius
Determine the maximum shearing stress in MPa of a helical spring composed of 20 turns and 19 mm wire diameter on a mean radius of 75 mm when the spring is supporting a load of 1000 N, assume the modulus of rigidity of 83 GPa.
The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating at 2100 rpm. The drive shaft material has an allowable shear stress of 230 MPa. i) Determine the maximum shear stress in the shaft. ii) In order to reduce the weight of the vehicle, a hollow shaft is proposed with a maximum outer diameter of 30 mm. Determine, the maximum inner diameter iii) Determine the resultant percentage weight reduction
Determine the maximum shearing stress and elongation in a bronze helical spring composed of 15 turns of 2.0-in.-diameter wire on a mean radius of 6 in. when the spring is supporting a load of 500 lb. G = 6 × 106 psi
Determine the maximum shear stress (in ksi). AT = 654 lb ft Diameter =3.7 in J =1.5in4 G = 11,000 ksi
A solid shaft is required to transmit 90 kW of power at 200 rpm. Determine the shaft diameter by the strength design and rigidity design and from this design choose the suitable diameter of the shaft, if the permissible stress for the material is 50 N/mm2 and the permissible twist is 10 per meter length. Also, determine the maximum shear strain acting on the shaft.Take modulus of rigidity = 150 GN/m2.
Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi.
A mild steel shaft transmits 18 kW at 450 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa
A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube is r1 = 45 mm and the measured angle of twist betweenthe ends is 0.5°, what is the shear strain γ1 (in radians) at the inners surface? b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to bekept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius(r2)max?
The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy = 250 MPa. Determine the safety factor at point A using the maximum shear stress theory. Select one: a. NA = 1.843 b. NA = 3.224 c. NA = 2.580 d. NA = 4.299

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

a) In the composite spring shown, Spring 1 has a mean coil diameter of 36 mm and a wire diameter of 3mm. Determine the wire diameter of spring 2 if it has a mean coil diameter of 24mm and the maximum shear stress in the two springs is to be the same.