The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20 bolts with diameter of 20 mm. The vessel has an outer diameter of 1 m. If the vessel has an internal gauge pressure of 1.77 MPa and experiences an external force 10.5 kN, determine the circumferential stress and the longitudinal stress in the vessel wall, the normal stress in the bolts, and the bearing stress on the plates due to the nuts on the bolts if the contact area on the nuts have an outer diameter of 37 mm and inner diameter of 20 mm.

The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20 bolts with diameter of 20 mm. The vessel has an outer diameter of 1 m. If the vessel has an internal gauge pressure of 1.77 MPa and experiences an external force 10.5 kN, determine the circumferential stress and the longitudinal stress in the vessel wall, the normal stress in the bolts, and the bearing stress on the plates due to the nuts on the bolts if the contact area on the nuts have an outer diameter of 37 mm and inner diameter of 20 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 2. Assume P = 80 kN and Q = 140 kN.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
Problem # 4: The tank shown is fabricated from steel plate. Determine the minimum thickness of plate which may be used if the stress is limited to 42 MPa and the internal pressure is 1.5 MPa. USING BOTH TANGENTIAL AND LONGITUDINAL STRESS FORMULA.
n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate. Answer a and b please
(c): How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders?
A 60-inch length of 2-inch OD x 1/8-inch wall 2014-T4 aluminum tube is supported by pinned supports at A and B as shown below. A 48-inch long pipe wrench is placed over the end of the tube at C as shown in the right view. (a) If a 200-lb person puts their full weight F on the end of the wrench handle will the tube material reach its yield point in shear? Use the maximum shear stress theory and show all calculations. (b) Where along the length of the tube, and in the tube cross-section, will the point of maximum shear stress be located? Be specific.
A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 105 MPa, of which 55 MPa is the initial stress? What circumferential stress is developed in the pipe? Why is it necessary to tighten the bolt initially, and what will happen if the steam pressure should cause the stress in the bolts to be twice the value of the initial stress? * Your answer A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 5 MN/m^2. (a) Determine the safe stress between the tangential and longitudinal sections in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MPa? (c) If the internal pressure were increased until the vessel burst,…
PLEASE ANSWER ASAP TY! a) Determine the cross-sectional area of the structural tube (in mm2) b) Determine moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum normal stress at point K (in MPa)? Include negative sign if compressive. d) What is the axial stress at section H-K (in MPa)? Include negative sign if compressive. e) What is the flexural stress at section H-K (in MPa)? f) What is the maximum normal stress at point H (in MPa)? Include negative sign if compressive.
1. A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The compression of the rod is 1.35 mm, and its diameter becomes 30.015 mm. Determine the modulus of elasticity (MPa) of the material. Assume the material does not yield. 2. Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a pressure of 1300 psi. The diameter of the vessel is 2 ft, and the stress is limited to 13 ksi.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the normal stress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (2).
Q4) two plate one lower fixed and one upper moved with a velocity 0.3 m/s , thedistance between the two plate is 0.3 mm and viscosity of the liquid is 0.65*10-3kg/m.s , calculate the shear stress on the upper plate .