The three conductors of a three phase line are arranged at the corners of a triangle of sides 5 m, 15 m and 9 m. The diameter of each line conductor is 2 cm. Calculate (i) Inductance per phase per km in mH (ii) Capacitance per phase per km in nF. Assume 50=8.854*10-12 F/m Inductance per phase per km in mH Capacitance per phase per km in nF

The three conductors of a three phase line are arranged at the corners of a triangle of sides 5 m, 15 m and 9 m. The diameter of each line conductor is 2 cm. Calculate (i) Inductance per phase per km in mH (ii) Capacitance per phase per km in nF. Assume 50=8.854*10-12 F/m Inductance per phase per km in mH Capacitance per phase per km in nF

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.14MCQ: For a three-phase three-wire line consisting of three solid cylindrical conductors each with radius...

See similar textbooks

Similar questions

A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1.5 cm diameter. The conductors are arranged in a horizontal configuration with 0.5 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux linkages, and (c) the total inductance of the line.
In terms of line-to-line capacitance, the line-to-neutral capacitance of a single-phase transmission line is Same Twice One-half
A 60-Hz, three-phase three-wire overhead line has solid cylindrical conductors arranged in the form of an equilateral triangle with 4-ft conductor spacing. The conductor diameter is 0.5 in. Calculate the positive-sequence inductance in Wm and the positive-sequence inductive reactance in /km.
Shield wires located above the phase conductors protect the phase conductors against lightning. True False
For a single-phase, two-wire line consisting of two solid cylindrical conductors of same radius, r, the total circuit inductance, also called loop inductance, is given by (in H/m) 2107ln(Dr) 4107ln(Dr) where r=e14r=0.778r
For a three-phase three-wire line consisting of three solid cylindrical conductors each with radius r and with equal phase spacing D between any two conductors, the inductance in H/m per phase is given by 2107ln(Dr)4107ln(Dr)6107ln(Dr) where r=e14r=0.778r
A 230-kV, 60-Hz, three-phase completely transposed overhead line has one ACSR 954 kcmil conductor per phase and flat horizontal phase spacing, with 7 m between adjacent conductors Determine the inductance in H/m and the inductive reactance in /km.
For the overhead line of configuration shown in Figure 4.33 operating at 60 Hz and a conductor temperature of 700C, determine the resistance per phase, inductive reactance in ohms/mile/phase, and the current-carrying capacity of the overhead line. Each conductor is ACSR Cardinal of Table A.4.
For a single-phase two-conductor line with composite conductors x and y, express the inductance of conductor x in terms of GMD and its GMR.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
For the case of double-circuit, bundle-conductor lines, the same method indicated in Problem 4.27 applies with r' replaced by the bundles GMR in the calculation of the overall GMR. Now consider a double-circuit configuration shown in Figure 4.36 that belongs to a 500-kV, three-phase line with bundle conductors of three subconductors at 21 in. spacing. The GMR of each subconductor is given to be 0.0485 ft. Determine the inductive reactance of the line in ohms per mile per phase. You may use XL=0.2794logGMDGMR/mi/phase
The capacitance of a single-circuit, three-phase transposed line with the configuration shown in Figure 4.38, including ground effect, and with conductors not equilaterally spaced is given by C20lnDeqrlnHmH8 F/mÂ line-to-neutral where Deq=D12D23D133=GMD r= conductors outside radiusHm=(H12H23H13)1/3HS=(H1H2H3)1/3 Now consider Figure 4.39 in which the configuration of a three-phase, single circuit, 345-kV line with conductors having an outside diameter of 1.065 in. is shown. Determine the capacitance to neutral in F/m, including the ground effect. Next, neglecting the effect of ground, see how the value changes.