The three forces F1 = 0.8 kN, F2 = 0.6 kN and F3 = 0.4 kN act on particle P as in the sketch. The angle θ is measured clockwise from the line of action of the vector F1 to the line of action of vector F3, and the tip of F3 coincides with the tail of F1. Represent the force system for the cases that (i) θ = 0◦ , (ii) θ = 30◦ , (iii) θ = 110◦ , (iv) θ = 245◦ and (v) θ = 270◦

The three forces F1 = 0.8 kN, F2 = 0.6 kN and F3 = 0.4 kN act on particle P as in the sketch. The angle θ is measured clockwise from the line of action of the vector F1 to the line of action of vector F3, and the tip of F3 coincides with the tail of F1. Represent the force system for the cases that (i) θ = 0◦ , (ii) θ = 30◦ , (iii) θ = 110◦ , (iv) θ = 245◦ and (v) θ = 270◦

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.9P: Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For...

See similar textbooks

Similar questions

Assume the following machine components are made of ductile material. Among which of the following more importance for stress concentration has to be given. a. Connecting rod operating at room temperature b. Shaft subjected to gradual static load c. All of the given answers d. Connecting rod made with defect
The Euler’s theory holds good for ________ Select one: a. Long column b. Short column c. Short shaft d. Long shaft
The resistance offered by a material to maintain the equilibrium is also called as Young’s modulus Strain Stress Internal energy
Select the correct general Tds relation(s)___________ A. B. C. D.
ANSWER THE FOURT PROBLEM ONLY
Suppose that P1 = 2 kN and P2= 5 kN (Figure 1) Find Fab,Fad,Fbc,Fcd,Fbd
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
9-8kN stress/force on the AB rope holding the base station shown below There are. In order for the net force at point A of this base station to be downward What is the stress/force that should be on the AC rope? A) 5556 N C) 7356 N B) 8200 N D) 3648 N E) 1228 N
The boom has a negligible weight, but has sufficient strength to support the 1000N load. Find the force in the boomBC. Refer to Figure d. a. 1577.50N c. 1154.70N b. 2,000N d. 577.35N
given: - initial length of steel tube= 200mm - aluminum rod is 0.175 mm shorter than steel tube. - l=0.175 mm properties of materials - ALUMINUM: coefficient of linear expansion: 23x10-6 /C modulus of elasticitty= 70 GPa - STEEL Coeficient of linear expansion: 11x10-6 /C Modulus of elasticity: 200 GPa *NEGLECT SHEAR AND LATERAL DEFORMATIONS. REQUIRED: - which of the two members will have contact on the rigid switch first and at what temperature - axial stress that would develop on 1st member after the 2nd material fills in the gap safely. PLS. SHOW FULL SOLUTIONS WITH BRIEF EXPLANATIONS AND NECESSARY DIAGRAMS...
Topic: Nonconcurrent, Nonparallel Forces
14 - If a 500 kg load is suspended on a hook with a used herbal rope with a base angle β = 30 °, what is the diameter of the rope? (sin 30 = 0.5, sin 60 = 0.87, cos 30 = 0.87, cos 60 = 0.5) A) 30,6mm B) 25.8mm C) 12.9mm D) 44,7mm E) 22,35mm