The total harmonic distortion (THD) of a signal x(t) is defined as “the ratio of the total RMS-value of the second and higher order harmonics to the RMS-value of the fundamental". The THD of the voltage u1(t)= b-cosot + c-sin(5ot-n/3) [V] (b, c: Constants; b<1) is given as 20%. Hence: a) Determine the relationship between a and b, if the form factor of the voltage u(t)= 2+ a + u:(t) [V] (a>0, const.) is given as 1.2. b) For a=1, calculate the active power drawn by the load in the figure. u(t) R 102 1H

The total harmonic distortion (THD) of a signal x(t) is defined as “the ratio of the total RMS-value of the second and higher order harmonics to the RMS-value of the fundamental". The THD of the voltage u1(t)= b-cosot + c-sin(5ot-n/3) [V] (b, c: Constants; b<1) is given as 20%. Hence: a) Determine the relationship between a and b, if the form factor of the voltage u(t)= 2+ a + u:(t) [V] (a>0, const.) is given as 1.2. b) For a=1, calculate the active power drawn by the load in the figure. u(t) R 102 1H

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the system defined by the first-order differential equation 100y'(t) + y(t) = x(t). a) Plot the log magnitude (dB)-log frequency graph of H(jw). b) The input is assumed to be suppressed when the magnitude of H(jw) is -40 dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest wa value in this case? Subject: Signals and Systems
Assume that the signal to be measured is displayed in the following form. y(t)=5sin1000t mV The time constant of the 1st order device is 100ms, K=1 V/V and its output is transferred to the 2nd order amplifier. The natural frequency and damping ratio of the amplifier is 15,000Hz and 0.8, respectively. Then, determine the expected output signal of y(t). And calculate the dynamic error and phase delay on the output. Is the chosen metrology system reasonable? If not, suggest a way.
Show that the derivative of a 1-D signal, I=I(x), amplifies the higher frequency components of the signal. Then, prove that even a slight amount of noise n=n(x), can be responsible for a large difference between the derivative I and I+n (Hint: Assume that n can be written as εsin(ωx) for some very small ε and very large ω).
A continuous time signal, x(t) = sin(20πt) + cos(40πt), is sampled uniformly at intervals of T to obtaina discrete time signal,x(n) = sin(πn/5) + cos(2πn/5).a) What is the value of T assuming no aliasing has occurred?b) Assume both frequency components have been aliased. In this case, is your choice of T unique? If not,specify some choices of T consistent with the information given
100 y(t)+ y (t) = X(t) for a system defined by a first-order differential equation:a. Draw the log magnitude(dB)-log frequency graph of H (jw) (phase graph is not requested. it is expected that the frequency axis will also be logarithmic when plotting the log magnitude graph).b. If the magnitude of H(jw) is -40 dB, it is assumed that the input is suppressed. it is given that the signal X (t) = coswat is suppressed by this system. What is the smallest wa value in this case?
In case the sound from the engine of a vehicle is modelled by the function y(t) = cos[ω(t + τ) + θ] where time delay=τ & phase=θ Determine the frequency & period of the signal u(t) whena)[ω, τ, θ] = [π/3, 1/2, π/2]b)[ω, τ, θ] = [3π/4, 1/2, π/4] N.b time should be in seconds & frequency in Hertz. c) y(t) = e-atu(t) for t≥0 & y(t) = 0 for t<0 where a>0 is a constant The function above defines the model of the decay of the vibration of a vehicle engine. i.Make a sketch of the signal y(t) & determime its fourier transform.
An Armstrong modulator is used to generate FM which is suitable for FM broadcasting.You are given input of narrowband FM signal with carrier frequency fc1 = 27 MHz anda frequency deviation Δf1= 17 kHz. Assume that the frequency multiplier with n = 3 andlocal oscillator frequency of 80 MHz. Calculate the output of the carrier frequency andfrequency deviation if additive frequency is selected by mixer. Explain your obtainedanswer.
An FM signal, eFM = 50 sin [2π(800k)t - 4 sin 2π(5k)t] is produced by a frequency modulator with -500Hz/V frequency deviation constant. Determine (a)Determine the equation of the carrier signal (b) What is the equation of the modulating signal (c) Determine the approximate bandwidth of the FM signal (use Carson’s Approximation)
For the system defined by the first-order differential equation: Draw the log magnitude (dB)-log frequency graph of H(jw). (The phase graph is not required. The frequency axis is expected to be logarithmic when drawing the log magnitude graph.) The input is assumed to be suppressed when the magnitude of H(jw) is -40dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest value of wa in this case?
In the figure, the input signal of the system is x (t) and the output signal is y (t). In this system, there is a sub-system with frequency response H (f). The frequency response H (f) of this subsystem is given at the top of the figure and defined as c = 800, k = 2. In addition, the frequency of the cosine signal shown in the figure is given as fc = 4000.x(t)= 4cos(8000πt).cos(1200πt)Find the output signal Y (t) and calculate the value at t = 1/4 , Y = 1/8 =?Given that the input signal of this system x (t) is defined as
1. The CT signal x(t)=3cos (600πt) + 6cos2 (mπt) is critically sampled (Nyquist rate)by fs=4000 Hz. Find:i. The value of m.ii. The frequency components of the signal.iii. The frequency resolution (Δf) of the output spectrum if the sampled signal isprocessed by 64 point-DFT.iv. Define frequency resolution.
During a vibration measurement experiment in the Mechanical Engineering Department at Hacettepe University, a piezoelectric accelerometer output is given by this mathemtaical equation: a (t) = 1 + 4 sin(43.98t) + 7sin(100.53t) in gravity acceleration (g) value. a) Determine the frequencies (in Hz) contained in the signal. Round your results to nearest integer value. b) What is the minimum sampling rate to avoid aliasing? c) Sketch clearly the frequency spectrum if the signal is sampled at 15 Hz. d) Now, the signal is filtered with a low-pass Butterworth filter to remove the maximum frequency component. It is desired to attenuate the amplitude of this component to at least 5 % of its value. If the sampling rate is now 20 Hz, what will be the order of the filter? e) If the blue one is our signal, then what is red and green ones? Write down the mathematical relation between the three signals? (Use labels as blue, red and green signal.)