The transfer function between the control voltage v(s) (the input) and the speed w(s), and the shaft angle 0(s) of the motion of a DC motor is given in the following figure; e,(s) K, v(s) w(s) G(s) G,(s) → „(s) 0.2 G(s) %D s + 0.104 1 G2 (s) : = - Find the steady state speed of the motor when an input voltage of v(t) = 10 volts is applied and the feedback loop is broken (i.e., motor is working open loop). b. Now assume feedback loop is active and find the closed loop transfer function а. m between 0 ,(s) and e„(s). m c. Calculate maximum value of K1 that can be used if an oversh desired. (You may use the figure in page 8 of this test.) of Mp<16% is

The transfer function between the control voltage v(s) (the input) and the speed w(s), and the shaft angle 0(s) of the motion of a DC motor is given in the following figure; e,(s) K, v(s) w(s) G(s) G,(s) → „(s) 0.2 G(s) %D s + 0.104 1 G2 (s) : = - Find the steady state speed of the motor when an input voltage of v(t) = 10 volts is applied and the feedback loop is broken (i.e., motor is working open loop). b. Now assume feedback loop is active and find the closed loop transfer function а. m between 0 ,(s) and e„(s). m c. Calculate maximum value of K1 that can be used if an oversh desired. (You may use the figure in page 8 of this test.) of Mp<16% is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Hi can you help me about this question? The figure shows a vehicle crash test simulation. Since the simplified model of the bumper of this vehicle is as follows, a- Find the transfer function of the system. X (s) / F (s) =? b- Assuming that the force F (t) is 1000 δ (t) N, find the displacement x (t). k=5000 N/m b=6000 N*s/m m= 1000 kg δ(t)=Dirac Delta
For the system shown in the attached image, assume A = 1300 and n = 860. Draw the root locus for K > 0 and find the range of K for closed-loop stability when:i. G(s) = Kii. G(s) = K(s + 200) / (s + 1000)
: If F(s) = s 4+ 5s3+20s 2 + 40s + 50 , Investigate the stability of this system
At t=0, a 1 pound force, denoted by f(t), is applied to the translational mechanical system. Determine K and M such that the response has a 1 second peak time and 4 second settling time if fv = 1. Additionally, what is the resulting overshoot percentage? Determine also the resulting transfer function as well as the steady state error for step input.
For the system with forward path gain G(s)=s+5s2+3s+2G(s)=s+5s2+3s+2 and feedback gain H(s)=1s+3H(s)=1s+3, input R(s)=8sR(s)=8s will be applied. Find the steady-state error (ess) that will occur in the system and enter it into the space given below
Given the plant transfer function, G(s) = 90/ s(s+4) and H(s) = 1. Obtain (i) characteristic equation (ii) damped frequency of oscillation (iii) damping ratio (iv) settling time (v) delay time
A DSP system is described by the following differential equation with zero initialcondition:y(n)+0.1y(n-1)-0.2y(n-2) =x(n)+x(n-1)a. Determine the impulse response y(n) due to the impulse sequence x(n) = (n).b. Determine system response y(n) due to the unit step function excitation, where u(n)= 1 for n  0.
A continuous time signal, x(t) = sin(20πt) + cos(40πt), is sampled uniformly at intervals of T to obtaina discrete time signal,x(n) = sin(πn/5) + cos(2πn/5).a) What is the value of T assuming no aliasing has occurred?b) Assume both frequency components have been aliased. In this case, is your choice of T unique? If not,specify some choices of T consistent with the information given
100 y(t)+ y (t) = X(t) for a system defined by a first-order differential equation:a. Draw the log magnitude(dB)-log frequency graph of H (jw) (phase graph is not requested. it is expected that the frequency axis will also be logarithmic when plotting the log magnitude graph).b. If the magnitude of H(jw) is -40 dB, it is assumed that the input is suppressed. it is given that the signal X (t) = coswat is suppressed by this system. What is the smallest wa value in this case?
For the sampled signal ws(n) = 12 + 8 cos((1/4)πn + 0.1) + 12 sin((3/4)πn − 0.2) generated by sampling w(t) at t = nT at a sampling frequency of fs = 1/T = 600 Hz, find expressions for w(t) with the following restrictions:a) Component frequencies range from 0 Hz to 300 Hzb) Component frequencies range from 300 Hz to 600 Hzc) Component frequencies range from 600 Hz to 900 Hz
a) Y(ω) = 1/(5+jω) The expression above defines the frequency domain signal Y(ω) from a time domain signal y(t) i) Determine the imaginary & real parts of Y(ω). ii.Determine the signal y(t) that produced the signal Y(ω). b)What are the 3 areas of application of i.Signals ii.Systems c) Briefly summarise with explanation the difference between discrete & continuous time signal and also write an expression that describes each signal type.
The input signal to an amplifier is vi(t)=0.01 cos(2000πt)+0.02 cos(4000πt). The gain of the amplifier as a function of frequency is given by A=10001+j(f/1000) Find an expression for the output signal of the amplifier as a function of time.