(a) Consider a system with impulse response given by h(t) = 3 x {u(t) – u(t – 2)}. An input signal x(t) = -2 x {u(t) – u(t – 3)} is applied to the system to produce the output y(t). (i) Sketch the waveforms of x(t) and h(t), respectively. (ii) Determine the system properties in terms of memory, causality and stability. (iii) Sketch the waveform of the output signal y(t).

(a) Consider a system with impulse response given by h(t) = 3 x {u(t) – u(t – 2)}. An input signal x(t) = -2 x {u(t) – u(t – 3)} is applied to the system to produce the output y(t). (i) Sketch the waveforms of x(t) and h(t), respectively. (ii) Determine the system properties in terms of memory, causality and stability. (iii) Sketch the waveform of the output signal y(t).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The impulse response of a continuous-time LTI system is given byh(t) = u(t) −u(t − 5) where u(t) is the unit step function.a) Find and plot the output y(t) of the system to the input signal x(t) = u(t) using the convolution integral.b) Determine stability and causality of the system.
Given the system, give the difference equation and the impulse response of the system, y(-1) = 2 y(-2)=1
The transfer function of a system is given in the image. (j is the imaginary part) Determine: (a) The impulse response. (b) Whether the system is stable. (c) The differential equation that represents the system.
A system has a damping ratio of 0.5, a natural frequency of 100 rad/s, and a dc gain of 1. Find the response of the system to a unit step input.
Samples of the discrete-time signal x[n] are given as x[n] = [-1, 2, 0, 3, -7, 6]. a) Calculate the odd and even components of x[n] b) Calculate the energy of the signal, y[n].
A system is described as: w (n + 1) = 0.5 w(n) — x(n) y(n) = w (n) - x(n) Where x(n) and y(n) are input and output signals, respectively. 1. Draw a block diagram or signal flow graph representation for this system by using Direct form II 2. Find the system function H(z) and the impulse response h(n) of this system. 3. Is this system causal or not? Why? 4. Is this system stable or not? why? 5. If the input impulse Dirac 8 find the difference equation.
Given a system with input x(t) and impulse response h(t) given by: x(t) = u(t) , h(t) = u(t) . Let y(t) be the output of the system. a) Find the equation of y(t) b) Sketch / Draw y(t)
I need help with the question below Consider a causal LTI continuous system described by the differential equation y′′(t) + 3y′(t) + 2y(t) = x(t) where y(t) is the system output and x(t) is the input.1. Find the transfer function H(s) of the system.2. Find its poles and zeros. From its poles and zeros, determine if the system is BIBO stable or not.3. If x(t) = u(t) and initial conditions are zero, determine the steady-state response yss(t)4. If the initial conditions were not zero, would you get the same steady state?. Explain
Measurements conducted on a servomechanism show the system response to be: C (t) = 0.3 e 60t + 1.5 e 10t, when subjected to a unit step input. [1].Obtain the expression for the closed-loop transfer function. [2].Determine the undamped natural frequency and damping ratio of the system.
Find the response Y(s) of the system described below: Note: Note that the initial conditions of the system are non-zero (i.e. ‡ 0).
1)For the circuit shown below, the initial conditions are zero and the switch is closed at t = 0.Datas: vg(t) = 10√2 sin (100t) [V] , R = 100 Ω , L = 2H ,C = 10-4 F.a)Get the circuit transfer function,H(s) = Vo(s)/Vi(s) in the standardized form.b)Calculate the damping factor and the natural frequency of the circuit. Rate the circuit with respectdamping.c)Determine the expressions of the input voltage in the time Vi(t) domain and the frequency domain Vi(s).
The response of a system, h(t) is given as in Figure 1 below where the amplitudeof this signal is 7. Then,this system is excited by an input of x(t) = (u(t) × (u(-t)+u(t))) /1. 1)Illustrate the input signal, x(t). 2)Calculate the convolution output of the system y(t) = x(t) ∗ h(t). Nextdetermine y(t) when t is 1 sec 2)Prove the solution in Q2 is comparable when solving in frequency domain(Laplace). Next, sketch the signal for convolution output.