The two bars are made of polystyrene, which has the stress-strain diagram shown in the figure below. The bars rupture simultaneously when the load P = 14.5 kN is applied. Assume that buckling does not occur. (Figure 1) (Figure 2) Part A Determine the cross-sectional area of bar BC. Express your answer to three significant figures and include the appropriate units. ABC = Value Units Submit Request Answer Figure < 1 of 2 Part B Determine the cross-sectional area of bar AB. Express your answer to three significant figures and include the appropriate units. 1.2 m OB HA ? 1 m A AB = Value Units Submit Request Answer

The two bars are made of polystyrene, which has the stress-strain diagram shown in the figure below. The bars rupture simultaneously when the load P = 14.5 kN is applied. Assume that buckling does not occur. (Figure 1) (Figure 2) Part A Determine the cross-sectional area of bar BC. Express your answer to three significant figures and include the appropriate units. ABC = Value Units Submit Request Answer Figure < 1 of 2 Part B Determine the cross-sectional area of bar AB. Express your answer to three significant figures and include the appropriate units. 1.2 m OB HA ? 1 m A AB = Value Units Submit Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10.24 A concrete canoe in storage is supported by two rope slings, as shown. each sling supports 48lb. The rope has a tensile breaking strength of 252lb. Determine the maximum value of theta if there is to be a factor of safety of 4.0 against breaking.
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter is reduced to 12.99265 mm. Determine: a. The modulus of elasticity. Answer: 200 GPa. b. Poisson's ratio. Answer: ν = 0.30 c. Shear modulus. Answer: G = 76.92 GPa. d. The deformation of the rod. Answer: δx = 0.09415 mm. Recommendation: Obtain the modulus of elasticity using the slope of the straight line.
A cylindrical rod AB has a length ? = 80 cm and a diameterof ? = 2 cm. The modulus of elasticity is ? = 200 GPa andyield strength is ?? = 300 MPa. The stress-strain diagram ofthe rod is shown in the left figure. A force ? = 100 kN isapplied to the bar and then fully removed (right figure).Determine the permanent set in the rod.
The two vertical rods attached to the light rigid bar in the figure are identical except for length. Before the load W was attached, the bar was horizontal and the rods were stress-free. Determine the load in each rod if W = 6600 lb. (Determine load for rod A & B in lbs)
A 2 m long steel wire is fixed and hanging vertically with a tensile loadof 2 kN and causes it to stretch by 4 mm. Determine the diameter ofthe steel wire when the modulus of elasticity is 205 GPa.A. 3.5 mm B. 5.5 mm C. 4.5 mm D. 2.5 mm
Determine the magnitude of the resultant of the external forces, K(kips) *kips(k)- a unit of force, equivalent to 1000lbs. (Av, Ah, Bv). Add figure if necessary.
rectangular steel plate, 1·2 m long and 850 mm wide, is subject to a compressive load along its length. If the width of the plate increases by 0·09 mm under load, determine its change in length. Take Poisson’s ratio for the steel as 0·28
Suppose that P= 1500 lb. Determine the force in each member of the cantilevered truss. Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. a) FDE b) FDF c) FGF
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.94 in2, A2 = 0.38 in2, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psi Your final answer should have three decimal places
At the limit of proportionality, a bar 30 mm wide (w) and 12 mm thick (t) elongates 2.0 mm under an axial load of 41.5 kN. The bar is 1.5 m long. If the Poisson's coefficient of the material is 0.33, determine: (a) the modulus of elasticity. E = ? (b) the variation in width. dw = ? (c) variation in thickness. dt = ?
Read the question carefully and give me right solution according to the question. Note: observe the given diagram and load carefully