The two springs (AB) and (AC) are shown, in figure (a) below, in their original unstretched position. After the application of a force F, the stretched position is shown in figure (b). The stiffness of spring (AC) is k(A) = 200 /ft The stiffness of the spring (AB), k(AB), is unknown. What would be the stretched length in spring (AC)? 3 ft KAB 3 ft F A KAC 200 4 2F+ 2f+ -2 ft b) (a) 4. ww

The two springs (AB) and (AC) are shown, in figure (a) below, in their original unstretched position. After the application of a force F, the stretched position is shown in figure (b). The stiffness of spring (AC) is k(A) = 200 /ft The stiffness of the spring (AB), k(AB), is unknown. What would be the stretched length in spring (AC)? 3 ft KAB 3 ft F A KAC 200 4 2F+ 2f+ -2 ft b) (a) 4. ww

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A uniform 80.0 N ladder 4.0 m long is placed against a frictionless wall with its base situated 2.0 m from the wall.Find the forces exerted by the wall and by the ground on the ladder.
A submarine is traveling at a depth of ‘95’ kilometers in the ocean, where the gagepressure is 840 Kg(f)/cm2 . The density and bulk modulus of elasticity of water at the top surface of the ocean are 1025 kg/m3 and 24000 kg(f)/cm2 respectively. Find the following:(i) What will be the density of water at the depth of 2.0 kilometers?(ii) What will be specific volume and change of volume at that depth?(iii) What is the pressure at the top surface of the submarine? How much will bechanged in pressure if submarine change direction from North to East?
6. There is air in the cylinder with the piston. The cross-sectional area of the piston is 5cm, the initial volume is 30cm, the pressure is 1 bar, and the temperature is 20℃. As shown in the picture next, the spring constant of the connected spring is ks=100 N/cm, and it is not deformed initially. By applying heat, the cylinder expands and the pressure in the cylinder becomes 4 bar. Answer the following questions. (hint: The relationship between P and V is straight) (1) Find the final volume (expressed in cm^3). (2) Find the expansion work during this process. (3) Find the amount of heat transfer during this process. Show this process on the P-v diagram
If a spring with elastic constant k [N/m] is deformed at distance x [m], then its potential energy is:
Six masses m1, m2, m3, m4, mM and mL, shown in figure below are to be completely balanced. The masses are : m1= 20.11 kg, m2 = 2 kg, m3 = 3 kg, m4= 6.3 kg, mM = 10.23 kg. The radii are : r1 = 0.1m, r2 = 0.12 m, r3 = 0.14 m, r4 = 0.12 m, rM = 0.1 m, rL = 0.5 m. The angles shown in the figure are: θ1 = 12º, θ2 = 103º, θ3 = 135º, Φ = 32º. The distances between different planes , shown in the figure are as follow: l1 =0.8 m, l2 = 0.7 m, l3 = 2.44 m. we need to find lm, l4 , mL and the angle α
‏A simply supported beam is subjected to two forces P and Q. Value of force P is 20 N and value of force Q is 40 N.If value of support force Ra is 30 N , then value of support force Rb is calculated as : O a . 70 N O b.30N O C60N O d . SON
In a jet wing test, engineers apply forces to the wing at points A, B, C, and D, perpendicular to the xz plane, as shown in the figure below. The positive y axis is oriented away from the page plan. The forces at A, B, C and D are 6000 lbs in the positive y direction, 4500 lbs in the direction negative y, 4000 lb in the positive y direction and 3000 lb in the positive y direction, respectively. Find the net force and equivalent moment with respect to point O. Use vector analysis to solve the question.
The hydraulic jack in the figure is used to lift a 1000 kg mass load to a height y2 = 150 mm. The diameter of the lift cylinder is D = 50 mm. With this information, analyze the system and determine. a) The pressure, in bar.b) The diameter d of the hand pump cylinder, so that the driving force F1 is 50 N. c) If the maximum displacement of the pump pistonfor y1 = 20 mm, how many drives will it take to fully lift the load? d) If you want to reduce the number of actuations by 2/3, keeping the diameter of the lift cylinder, D, the same actuation force F1, and the stroke y1, what geometric changes can be made in the system?
Packaging and distribution system in a factory, through a spring and conveyor beltreferences As given by the figure, the boxes are left on the spring and pushed onto the conveyor belt. The boxes are originally located on uncompressed broadcast h up. When they are left, boxes, each with a mass of m, compress the spring as much as ΔL. All potential energy of the box in the spring is converted into elastic energy. calculate ΔL as [m] for M = 5 kg, spring constant k = 262 N/M, h = 0.85 m, and gravity acceleration g = 9.81 m/s2.
The blood pressure in your heart is 1.52 x104 Pa. If an artery in the brain is 0.421 m above the heart, what is the pressure in the artery?
A 4.2‑kg brown hare walks on a horizontal beam (the beam's mass m = 2.8 kg and length a = 2.4 m). The beam is suspended with two ropes attached to the ends of the beam. What should be the distance between the hare and the left end of the beam so that the tension in the left rope is three times as big as the tension in the right rope? 1. The distance from the left end, b = If the hare is at the distance found in the previous question, calculate the tension in each rope. 2. The tension in the left rope, T1 = 3. The tension in the right rope, T2 = ------------------------------------------------------------------ A bike wheel has a radius of R = 0.62 m and a mass of m = 2.6 kg spins at 270 rpm. What is the angular momentum of the wheel? Assume that the wheel has a shape of a ring. The angular momentum of the wheel, L ? A typical bowling ball might have a mass of 7 kg and a radius of 12 cm. How fast the ball should spin to have the same angular momentum as the wheel from the…
Mountaineersoften use a rope to lower themselvesdown the face of a cliff (this is called rappelling).They do this with their body nearly horizontaland their feet pushing against the cliff. Suppose that an 82.0 kg climber,who is 1.90 m tall and has a center of gravity1.1 m from his feet, rappels down a verticalcliff with his body raised 35.0° above the horizontal.He holds the rope 1.40 m from his feet,and it makes a 25.0° angle with the cliff face.(a) What tension does his rope need to support?(b) Find the horizontal and vertical componentsof the force that the cliff face exerts on theclimber’s feet. (c) What minimum coefficientof static friction is needed to prevent the climber’sfeet from slipping on the cliff face if he hasone foot at a time against the cliff?