Q2) Figure 2 shows a rope that is stretched between points A and C, there is mass m at point B. Given values: m=20 kg, h= 2 m, d=3 m, a= 30°, y-60°. Determine the followings: a) What are the values of lengths LAB and LBC must be selected according to the given angles a and y? b) What are the values of forces FAB and Fsc in the rope sections AB and BC? A AB B. Y Figure 2 m C g

Q2) Figure 2 shows a rope that is stretched between points A and C, there is mass m at point B. Given values: m=20 kg, h= 2 m, d=3 m, a= 30°, y-60°. Determine the followings: a) What are the values of lengths LAB and LBC must be selected according to the given angles a and y? b) What are the values of forces FAB and Fsc in the rope sections AB and BC? A AB B. Y Figure 2 m C g

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A submarine is traveling at a depth of ‘95’ kilometers in the ocean, where the gagepressure is 840 Kg(f)/cm2 . The density and bulk modulus of elasticity of water at the top surface of the ocean are 1025 kg/m3 and 24000 kg(f)/cm2 respectively. Find the following:(i) What will be the density of water at the depth of 2.0 kilometers?(ii) What will be specific volume and change of volume at that depth?(iii) What is the pressure at the top surface of the submarine? How much will bechanged in pressure if submarine change direction from North to East?
How many cables supporting the mass M ? mass (M) 400 kg as shown in the figure below. If a = 4 m, b = 5 m, c = 3 m, k1= 5000 N/mm and k2= 4000 N/mm.
Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal. Response
As shown, a mass is hung from the pulley. This mass causes a tensile force of 11.0 N in the cable and the pulley to hang h = 130.0 cm from the ceiling. Assume that the pulley has no mass. What is the weight of the mass?
In a jet wing test, engineers apply forces to the wing at points A, B, C, and D, perpendicular to the xz plane, as shown in the figure below. The positive y axis is oriented away from the page plan. The forces at A, B, C and D are 6000 lbs in the positive y direction, 4500 lbs in the direction negative y, 4000 lb in the positive y direction and 3000 lb in the positive y direction, respectively. Find the net force and equivalent moment with respect to point O. Use vector analysis to solve the question.
Two ladders, 4.00 m and 3.00 m long, are hinged at point A and tied together by a horizontal rope 0.90 m above the floor (Fig. ). The ladders weigh 480 N and 360 N, respectively, and the center of gravity of each is at its center. Assume that the floor is freshly waxed and frictionless. (a) Find the upward force at the bottom of each ladder. (b) Find the tension in the rope. (c) Find the magnitude of the force one ladder exerts on the other at point A. (d) If an 800 N painter stands at point A, find the tension in the horizontal rope.
2. A ladder 12 m long leans against a vertical frictionless wall with its lower end 3 m from the wall. The ladder weighs 40 N. Find the magnitude and direction of the force exerted on the lower end of the ladder. 3. A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A exerts a force of 20 N, where must a load of 45 N be placed on the beam? b) What force does B exert?
A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. Suppose m = 2.0kg, L = .60m, M = 0.50kg, and angle(theta) = degrees. a. Using numbers, what is the magnitude of the tension force in the rope connecting the board and wall? b. Using numbers, what is the magnitude of the force applied by the hinge? c. Using numbers, in what direction does the force applied by the hinge point?
Find the compression length of a spring if a 100 pound weight if dropped from 8 ft onto a spring with constant of 33.33 lb/in. The correct answer is 2.266 ft.
A chandelier is hung as shown below. The wires will snap if the tension exceeds 500 N. What is the maximum mass of the chandelier?
A) Imagine a procedure used for the execution of a certain work, as shown in the following figure. Such a crane has a mass of 1000 kg and is transporting a coffin with a total mass of 2400 kg. Assume that support A is fixed, support B is movable, and point G is the center of gravity of the lift. What are the support responses in kN? Question 1 options: a) The support responses are as follows: Rax = Rbx = 34 kN and Ray = 109.33 kN. b) The supporting responses are as follows: Rax = Ray = 109.33 kN and Rbx = 34 kN. c) The support responses are as follows: Rax = 56.8 kN; Rbx = 109.33 kN and Radius = 34 kN. d) The support responses are as follows: Rax = 156.7 kN; Rbx = 89.65 kN and Radius = 34 kN. e) The supporting responses are as follows: Rax = Rbx = 109.33 kN and Ray = 34 kN. B. Consider the beam shown in the following figure. In this beam, there are different types of existing forces, such as applied moment, distributed load and point load. Knowing the magnitude of each of the forces,…
A uniform bar 6 m long is held by ropes at the ends making angle 60° and 30°, respectively, with the horizontal. A weight of 400 N is hung 1.0 m from the left end where the 60° rope is attached. Find the tension in the rope and the weight of the bar.