The two uniform slender bars constructed from the same stock material are freely pinned together at B. Determine the minimum angle 0 at which slipping does not occur at either contact point A or C. The coefficient of static friction at both A and C is u = 0.50. Consider only motion in the vertical plane shown. B Ae

The two uniform slender bars constructed from the same stock material are freely pinned together at B. Determine the minimum angle 0 at which slipping does not occur at either contact point A or C. The coefficient of static friction at both A and C is u = 0.50. Consider only motion in the vertical plane shown. B Ae

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.88RP: The panel of weight W with its center of gravity at G is placed between vertical guides and...

See similar textbooks

Similar questions

The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The uniform bar of weight W is supported by a ball-and-socket joint at A and rests against a vertical wall at B. If sliding impends when the bar is in the position shown, determine the static coefficient of friction at B. [Hint The direction of impending sliding is tangent to the dashed circle (the potential path of motion of point B).]
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
The two uniform sheets of plywood, each of length L and weight W, are propped as shown. If the coefficient of static friction is 0.5 at all three contact surfaces, determine whether the sheets will remain at rest.
The panel of weight W with its center of gravity at G is placed between vertical guides and released. Determine the largest height h for which the panel will not slide down due to binding at corners A and B. The coefficient of static friction between the panel and the guides is 0.5.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The 120-kg block A is suspended from a rope that runs around the fixed pegs B and C. The coefficient of static friction between the pegs and the rope is 0.25. Determine the range of the force P for which the system is in equilibrium.