Calculate the horizontal force P on the light 12° wedge necessary to initiate movement of the 41-kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.26. Also determine the friction force FB at point B. (Caution: Check carefully your assumption of where slipping occurs.) P Answers: P= FB = i 367 i -222 129 41 kg B N A N

Calculate the horizontal force P on the light 12° wedge necessary to initiate movement of the 41-kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.26. Also determine the friction force FB at point B. (Caution: Check carefully your assumption of where slipping occurs.) P Answers: P= FB = i 367 i -222 129 41 kg B N A N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.16P: The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient...

See similar textbooks

Similar questions

The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
For Probs. 4.61â€“4.68, (a) draw the free-body diagrams for the entire assembly (or structure) and each of its parts. Neglect friction and the weights of the members unless specified otherwise. Be sure to indicate all relevant dimensions. For each problem, (b) determine the total number of unknown forces and the total number of independent equilibrium equations.
Calculate the horizontal force P on the light 11° wedge necessary to initiate movement of the 38-kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.29. Also determine the friction force FB at point B. (Caution: Check carefully your assumption of where slipping occurs.)
AB and BC bars which are connected at pin B, each having a mass of 100 kg, as shown in the figure. If the coefficient static friction at piont C is 0.5 , determine the maximum value of force P for the system to be in static equilibrium.
Determine the force P required to move the wedge to the right if the coefficient of static friction is 0.35 at all contact surface (Figure 3). The uniform cylinder weight, W is 20 kN, and the weight of the wedge may be neglected.