The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which is in tension as shown.1.5 m60°B-1.2 mWhat is the magnitude of the Vertical reaction force at O(Answer in Newtons)Answer:Nex

Using cosine rule : AB2=1.22+1.52-2(1.2)(1.5)cos120°=3.69+1.8AB=5.49=2.343 m using sine rule:…

The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which is in tension as shown. 1.5 m 60° 1.2 m What is the magnitude of the Vertical reaction force at O (Answer in Newtons) Answer:

The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which is in tension as shown. 1.5 m 60° 1.2 m What is the magnitude of the Vertical reaction force at O (Answer in Newtons) Answer:

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.84P: The cable supports three 400-lb loads as shown. If the maximum allowable tension in the cable is 900...

See similar textbooks

Related questions

Q: 2.) (2 points) The cylinder as shown below weighs 1000 N. It is supported by a rod with a cable at…

Q: 3/63 A uniform steel plate 18 in. square weighing 68 lb is suspended in the horizontal plane by the…

A: The side of the square plate is a=18 in. The weight of the plate is W=68 lb.

Q: The 20 × 20-in. square plate shown weighs 56 lb and is supported by three vertical wires. Determine…

A: The tension in the wire is shown below – The tension in the wire is shown below –

Q: Two men exert forces F and P on the ropes. If P = 48 Ib, what is the required force F to maintain…

A: ....

Q: The cable shown in Fig. If the sag ha in the cable is 200 m, determine weighs 30 N/m. The tension in…

A: Write the expression for tension in the cable.

Q: In the assembly shown, rod AB is made of steel (E = 200 GPa) and has a diameter D = 50 mm. Rod BC is…

A: Given data: STEEL…

Q: A uniform 0.40 kN boom is supported as shown. Find the tension in the tie rope and the components of…

A: Consider the free body diagram shown below for the given system.

Q: Q2: The structure shown in the diagram ( one ofthe two identical structures that support the scoop…

A: We need to draw FBD and resolve forces first

Q: The given truss below is loaded vertically downward with 4KN and 8KN at points C and D,…

Q: Determine all forces acting on member ACD of the The diameter of the pulley at D frame shown in Fig.…

A: Given data Weight of the body W = 500lb To determine the forces acting at ACD in the frame

Q: For the shown frame structure, the uniform beam AB weighs 480 lb and the uniform column CF weighs…

Q: (6) The 68 lb uniform square plate is suspended by three vertical wires as shown so that the plate…

A: Given:- Weight of the plate (W) = 68 lb Suspended by three vertical wires A, B and C To Find:-…

Q: The uniform bar with end rollers weighs 65 Ib and is supported by the horizontal and vertical…

Q: 0.6 m 500 N 2000 N 0.3 m 0.2 m 0.4 m 0.3 m

A: a) The free body diagram of the frame can be drawn as, Calculate the angle θ. Calculate the…

Q: B D - W 2W - L/2 L/2 * L/2 L/2

Q: Helght 3 3' 4' 500 lb B.

A: A structure made up of several bars (or members) riveted or welded together is known as truss. If…

Q: The rectangular plate shown weighs 80 lb and is supported by three vertical wires. Determine the…

A: Consider the free body diagram shown below for the given rectangular plate.

Q: The beam supports two loads, w;(x) = 20x² + 100, where w, is in lb/ft and x is in ft, and a linearly…

A: Given Data: The load w1=20x2+100 and a span of 0'<x3' The linearly varying load is from 280 lb…

Q: 1. For the frame shown, Solve for the reaction at the roller support at A and the horizontal and…

Q: A uniform plank 8 ft long is balanced on a corner If using a horizontal force of 75 lb as shown in…

A: Let's draw free body diagram of 'AB' as shown in figure. Here, W=45 lb

Q: The given truss below is loaded vertically downward with 4KN and 8KN at points C and D,…

Q: The boom AB supports a load of W = 720 lb. The boom is supported by a ball-and-socket joint at A and…

Q: The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which…

A: Given information: The mass of the rod (m) = 18 kg From The figure we can calculate the angel "α"…

Q: A uniform rod is attached to a wall by a hinge at its base. The rod has a mass of 3.5 kg, a length…

Q: The figure shows a right triangle-shaped rigid body, its mass is m (kgl, and it is supported by a…

Q: . The automobile bumper jack shown at Fig. 3 is subjected to a 4000 N downwar oad. Starting with a…

Q: The given truss below is loaded vertically downward with 4KN and 8KN at points C and D,…

Q: 4. A pipe strut BC is loaded and supported as shown. The strut has a uniform cross section nd a mass…

A: Answer: (a) The tension in the coal is 498.1 N. (b) The reaction at support C is 898 N.

Q: - Draw a free-body diagram of the ring at A and identify each force. 30 200 N 500 N

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

Q: For the pulleys system shown below, if each pulley has 80 N weight, answer the following to be the…

Q: 3. A 60 pound force is attached to the 90° weightless bar ABCD at point B as shown below. The bar is…

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A: Given that The force P→ is 19i^-10j^ KNThe coordinates from the figure are:A 2,0,-3; B (0,6,0); C…

Q: The cylinder as shown below weighs 1000 N. It is supported by a rod with a cable at point B.…

Q: 3. A 60 pound force is attached to the 90° weightless bar ABCD at point B as shown below. The bar is…

Q: 3.9 The homogeneous 18-kg pulley is attached to the bar ABC with a pin at B. The mass of the bar is…

Q: Activity 3. From a bar subjected by an axial force P, Draw the components of P acting on the…

Q: 1. The telephone pole AB weighing 3730 N is resting in a hole that is 2 m deep. If the contact force…

Q: A rectangular plate 20-kg is supported by three cables as shown etermine: 1.1 Drawing…

Q: A 150-lb cylinder is supported by two cables AC and BC that are attached to the top of vertical…

A: The free body diagram is shown below, The coordinate of point A is given as, A=-10.8,15,0 The…

Q: The 45 Ibs. square plate shown is supported by three vertical wires. Determine the tension in each…

A: Given figure Given data : The 45 lbs. square plate shown is supported by three vertical wires. To…

Q: The Free-Body diagram for joint D is drawn assuming that all internal forces are in tension. Solve…

A: From Equilibrium conditions 1. sum of vertical forces are zero. 2. sum of horizontal forces are zero

Q: The 6 m uniform rod as shown below weighs 1000 N. Segment AB and BC is 4 m long. The cable acts at a…

Q: The vertical pole shown carries two utility lines represented by the tensions T, and T2. For…

Q: A 225 Kg crate, as shown, is supported by three cords. One cord has a spring in it. Set k= 1.5 kN/m

Q: The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which…

Q: determine the tension T

A: To determine tension T in the cable

Q: One end of a post weighing 400 Nand with height h rests on a roughhorizontal surface with ms =…

A: Given Weight = 400 N Angle = 36.9 To find Magnitude of F for mid point Magnitude of F if applied…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which is in tension as shown.
1.5 m
60°
B
-1.2 m
What is the magnitude of the Vertical reaction force at O
(Answer in Newtons)
Answer:
Nex

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B, the sag in the cable is 5 m. Find the span L of the cable.
The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at A. Draw the FBD for the bar, recognizing that it is a two-force body. Determine the number of unknowns.
The cable supports three 400-lb loads as shown. If the maximum allowable tension in the cable is 900 lb, find the smallest possible sag hC at C.
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The homogeneous plate of weight W is suspended from two cables. Determine the force P that is necessary to keep the plate in the position shown.
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
a rectangular plate 20-kg supported by three cable as shown determine: 1.1 drawing free body diagram (FBD) 1.2 tension in each cable.
The ABD bracket is supported by a pin at A and the cable DE. Determine the internal forces immediately to the left of the load.Template: (On CD) F= 270 N; M=43.2 N.m; V = 90 N
The frictionless slider B has a frictionless pulley mounted to it, around which is wrapped a cable that supports weight W = 180 lb as shown. The pulley at D is also frictionless, and member BE is a bar. If α = 55° determine the force in bar BE.