In the assembly shown, rod AB is made of steel (E = 200 GPa) and has a diameter D = 50 mm. Rod BC is made of aluminum (E = 70 GPa) and has a diameter d = 30 mm. Two forces are applied to the assembly as shown. If P = 1600 N, determine the support forces at A and C. Hint: The system is statically indeterminate. A В P C D d Aluminum Steel

In the assembly shown, rod AB is made of steel (E = 200 GPa) and has a diameter D = 50 mm. Rod BC is made of aluminum (E = 70 GPa) and has a diameter d = 30 mm. Two forces are applied to the assembly as shown. If P = 1600 N, determine the support forces at A and C. Hint: The system is statically indeterminate. A В P C D d Aluminum Steel

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.19P: The three bars are welded together to form a rigid unit that is supported by three slider bearings....

See similar textbooks

Similar questions

The ABD bracket is supported by a pin at A and the cable DE. Determine the internal forces immediately to the left of the load.Template: (On CD) F= 270 N; M=43.2 N.m; V = 90 N
The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. If the downward force P will produce a 50 mm vertical displacement at the free end of lever AC, determine the force P if G = 83 GPa.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between the wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. Determine the magnitude of the member CD. Is the member in tension or compression? Determine the support reactions at A. Determine the unstretched length of the spring EF given a spring constant of 150 kN/m.
Determine the internal forces at point D of the frame shown in the figure.
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure, choose the alternatives that are true. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N If the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position. True or false?
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N Which option is right? a) if the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position or b) if the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position
This structure is supported by a roller joint on the left and a pin joint on the top. Two loads, P have similar magnitudes of P = 650 N and the angle θ = 40°. The length L of both members is 1.5 m. The vertical load acts at the midpoint of the horizontal member. Solve for the reaction forces at the roller and pinned joints.
The collar C is fixed to rod AB using a glued bond that allows a maximum force of 405 N parallel to the axis of the rod. The collar has weight W acting in the negative z direction. Determine the weight W in N of the collar that will cause the glued bond to break as shown in figure.
Determine the forces in each member using any method discussed in your theory of structures/mechanics. Using Software is not allowed. Show complete solution and tabulate your answers indicating whether it is compression or tension. Use Pn = 205 kN, Po = Zero
Before the load is placed on the rigid plate, the top of the central spring is 20 mm lower than the outer springs. Each outer spring is made of 24 turns of 15-mm diameter wire on a mean radius of 60 mm. The central spring consists of 16 turns of 20 mm dimeter wire on a mean radius of 80 mm. If a load P = 5 kN is now placed on the rigid plate. Disregarding the weight of the plate, use G = 83 GPa and use Light spring formula. Determine the maximum shearing stress of the in uter spring. In MPa
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.