The uniform beam has weight W. Determine the average tension in each of the two cables AB and AC if the beam is given an upward speed v in time t starting from rest. Neglect the mass of the cables. Units Used: EN = 10° N Given:
Q: *15-4. Each of the cables can sustain a maximum tension of 5000 lb. If the uniform beam has a weight…
A: 15-4 The free body diagram of the cables is as follows: Calculate the forces in the vertical…
Q: The gantry structure is used to test the response of an airplane during a clash. The plane of mass…
A:
Q: The system is released from rest with no slack in the cable and with the spring unstretched.…
A:
Q: If the motor draws in the cable with an acceleration of 3 m/s?, determine the reactions at the…
A:
Q: The 1000 kg roller coaster car is released from rest at A as shown in the figure below. Find the…
A: Given:m=1000 Kgr=7.5 ms=20 mAs the coster goes round the curve it will be acted by centrifugal…
Q: The 280-Mg jet airliner has three engines, each of which produces a nearly constant thrust of 229 kN…
A:
Q: he roller coaster car has a mass of 700 kg, including its passenger. If it starts from the top of…
A:
Q: The tractor-trailer unit is moving down the incline with a speed of 5.2 mi/hr when the driver brakes…
A:
Q: The 251-Mg jet airliner has three engines, each of which produces a nearly constant thrust of 230 kN…
A:
Q: The system is released from rest with no slack in the cable and with the spring stretched 200 mm.…
A: Given that: mass of the cart = 10 kg the spring is stretched by 200 mm it is required to determine:…
Q: The door has a weight of 200 lb and a center of gravity at G. Determine the constant force F that…
A: Given data: *The weight of the door is w=200 lb. *The distance required to move the door is s=12 ft.…
Q: Determine the speed v which the 630-kg four-man bobsled must have in order to negotiate the turn…
A:
Q: The system is released from rest with no slack in the cable and with the spring stretched 220 mm.…
A: Given data: x1=220 mm=0.22 mM=16 kgv1=v2=0 Need to determine the distance travelled by the cart…
Q: The system is released from rest with no slack in the cable and with the spring stretched 200 mm.…
A:
Q: Penundulum is released from rest when 0 = 0, has a mass of m, determine the tension in string BC as…
A: Represent the forces on the bob when the bob is at rest and position θ. In triangle AOC,
Q: The spring has an unstretched length of 0.4m and a stiffness of 200N/m. The 3 kg slider and attached…
A:
Q: The 332-Mg jet airliner has three engines, each of which produces a nearly constant thrust of 213 kN…
A:
Q: The winding drum D is drawing in the cable at an accelerated rate of 4.5 m/s^2. Determine the cable…
A: Given Mass, M = 1000 kg Acceleration, a = 4.5 m/s2 Find Tension in the cable, T
Q: The spring attached to the 1.8-kg block is undeformed when the system is in the position shown. The…
A: Write the formula for the potential energy of the spring when it touches the ground. E=12kx2 Here, x…
Q: The system is released from rest with no slack in the cable and with the spring stretched 110 mm.…
A:
Q: Determine the speed v which the 670-kg four-man bobsled must have in order to negotiate the turn…
A: Mass =670kg, Find, V and N
Q: If the 50-kg load A is hoisted by motor M so that the load has a constant velocity of 1.5 m/s,…
A:
Q: spring of stiffness k = 500 N/m is mounted against the 10-kg block as shown in the figure (4). If…
A:
Q: The roller coaster car has a mass of 700 kg, including its passenger. If it starts from the top of…
A:
Q: Q7 -8 The roller-coaster car has a speed of 20 ft/s when it is at the crest of a vertical parabolic…
A:
Q: The casting has a mass of 4 Mg, suspended in a vertical position and initially at rest, it is given…
A: Given data: The mass of the casting is m = 4 Mg = 4000 kgThe initial speed of the casting in the…
Q: Q4/ Assuming the car has no dependence on friction with the road, determine the speed u of the car.…
A: r = 365 m u = 0.8
Q: The system is released from rest with no slack in the cable and with the spring stretched 260 mm.…
A:
Q: A pilot weighs 150 lb and is traveling at a constant speed of 120 ft/s. Determine the normal force…
A: Given: W= 150 lb →m=Wg=15032.2lbm V = 120 ft/s and radius (r) = 400 ft
Q: Problem 13-55 The plane is traveling at a constant speed v along the curve y = bx2 + c. If the pilot…
A: Data given- b = 60×10-6 m-1 c = 1500 m W = 900 N v = 240 m/s
Q: 1. The motor at B winds up the cord attached to the 65 lb crate with a constant speed. Determine the…
A: Given data given pulley system.
Q: The cart carrying the small 2-kg package A is moving up the incline with constant acceleration N. If…
A:
Q: The sports car, having a mass of 1700 kg is travelling horizontally along a 20° banked track which…
A: Data given- M = 1700 kg Theta = 20° R = 100 m Coefficient of friction = 0.2
Q: The motor winds in the cable with a constant acceleration, such that the 20kg crate…
A: Given question belongs to the subject Classical Mechanics and be solved using Newton's second law…
Q: y y- 4.5 - h ft k lblft B I ft The 8-lb collar has a speed of 9 ft. s at A. The attached spring has…
A:
Q: Determine the speed v which the 685-kg four-man bobsled must have in order to negotiate the turn…
A: Given: m=685 Kg radius r=59 m
Q: The motor winds in the cable with a constant acceleration, such that the 20-kg crate moves a…
A:
Q: The 300-Mg jet airliner has three engines, each of which produces a nearly constant thrust of 240 kN…
A:
Q: The automobile has a weight of 1000 kg and crashes into the wall. If the impact occurs in 0.05 s,…
A: Impulse is given as F*dt
Q: Determine the speed v which the 690-kg four-man bobsled must have in order to negotiate the turn…
A: Given data- Mass = 690 kg Find the speed and normal force on the bobsled.
Q: The two springs are identical, with unstretched length 0.4 m. When the 150-kg mass is suspended at…
A:
Q: *15–4. Each of the cables can sustain a maximum tension of 5000 lb. If the uniform beam has a weight…
A:
Q: The system is released from rest with no slack in the cable and with the spring stretched 100 mm.…
A: We have given
Q: Q4/ Assuming the car has no dependence on friction with the road, determine the speed u of the car.…
A: Given:Coefficient of static friction, μ=0.8θ=40or=365 m
Q: E A bead with a mass of 0.25 kg is released from rest at A and slides down and around the fixed…
A: Given data as per the question Mass =0.25 kg Calculations considering point A as the datum apply…
Q: The 10-lb collar starts from rest at A and is lifted by applying a constant vertical force of F = 25…
A: Given: The mass of collar, m = 10 lb The vertical force, F = 25 lb The angle, θ = 60°
Q: The 40 kg crate is moving downward at 10 m/s. The motor M pulls on the cable with a force of F,…
A: Given data Assuming upward motion as positive.
Q: Each of the cables can sustain a maximum tension of 5000 lb. The uniform beam has a weight of 4200…
A:
Q: The block of weight W is released from rest at A and slides down the smooth circular surface AB. It…
A: Given data: The weight of the block is W=25 N The value of a is a=0.9 m The value of b is b=0.6 m…
Q: Find the acceleration of the blocks and the tension in the chord if both have a mass equal to 100…
A:
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- The 20kg uniform rectangular plate is supported by an ideal pivot at O and a spring which must be compressed prior to being slipped into place at point A. If the modulus of the spring is k=2KN/m, what must be its undeformed length?A spring with squared and ground ends has 16 active coils diameter of 6 mm and pitch of 10 mm . If spring rate is 85 KN/m , determine the solid force?1)Calculate the velocity of the arm, observed by a stationary person on the ground.2)Draw the FBD of the combined body (crane body, arm and load).3)Is the combined body stable? Why?4)Calculate the moment of the following, about wheel A,i) combined crane bodyii) load mass5)Which combined body’s component(s) will not fail? Why? (Hint: The crane was initially in equilibrium.)6)What are the various limits (maximum or minimum) for the combined body to be stable? Explain why.
- QUESTION: It is wanted to withdraw from A end with V_A velocity velocity (a_A = 0 m / s ^ 2) as shown on AB rod. Find the force F that will satisfy this condition. In this case, what are the support reactions at A and B points? Ignore the mass and atalat moments (I) and friction forces of the wheels. The inertia moment table of the rod is given.A stationary bicycle wheel of radius 0.7 m is mounted in the vertical plane (see figure below). The axle is held up by supports that are not shown, and the wheel is free to rotate on the nearly frictionless axle. The wheel has mass 4.3 kg, all concentrated in the rim (the spokes have negligible mass). A lump of clay with mass 0.5 kg falls and sticks to the outer edge of the wheel at the location shown. Just before the impact the clay has speed 8 m/s, and the wheel is rotating clockwise with angular speed 0.27 rad/s. Assume +x is to the right, +y is upward, and +z is out of the page. Assume the line connecting the center to the point of impact is at an angle of 45° from the horizontal.Just after the impact, what is the angular velocity (magnitude and direction) of the wheel?The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of gravity, kG = 250 mm. Whereas there is no slip, determine the elastic force after it rotates 90 ° clockwise from illustrated position. The AB spring has a constant stiffness k = 100 N / m and a length in the undisturbed situation of 500 mm. Consider that the wheel is initially at rest.
- Please provide complete solutions and illustrations for the problem below. The bent bar shown in the figure weighs 24kg/m and is free to rotate in a vertical plane about a horizontal axis at A. Compute the X & Y components of the bearing reaction at A an instant after it is released from rest at the given position.The beam, uniform in mass, M = 47.6 kg and length L = 10.2 m, hangs by a cable supported at point B, and rotates without friction around point A. On the end far of the beam, an object of mass m = 24.3 kg is hanging. The beam is making an angle of θ = 30.9° at point A with respect to the + x-axis. The cable makes an angle φ = 21.1° with respect to the - x-axis at B. Assume ψ = θ + φ. a. Enter an expression for the lever arm for the weight of the beam, lB, about the point A. b. Find an expression for the lever arm for the weight of the mass, lm. c. Write an expression for the magnitude of the torque about point A created by the tension T. Give your answer in terms of the tension T and the other given parameters and trigonometric functions. d. What is the magnitude, in newtons, of the tension in the cable? e. Enter an expression the horizontal component of the force, Sx, that the wall exerts on the beam at point A in terms of the tension T, given parameters, and variables…Write an expression for how far the spring is stretch when the cart is at rest in the equilibrium position. Name thisdistance y-naught. Thanks!
- PROBLEM 1: The uniform beam has a mass of 50 kg per meter of length. Support at A is roller and support at B is hinge. Use acceleration due to gravity = 9.81 m/s2. [1] Calculate the reaction at A. (ANSWER: 1.86 KN) [2] Calculate the horizontal reaction at B. (ANSWER: 0.00 KN) [3] Calculate the vertical reaction at B. (ANSWER: 2.84 KN)A baseball attachment that helps people with mobility impairments play T-ball and baseball is powered by a spring that is unstretched at position 2. The spring is attached to a cord that is fastened to point B on the 75-mm radius pulley. The pulley is fixed at point O , rotates backwards to the cocked position at 0 , and the rope wraps around the pulley and stretches the spring with a stiffness of k = 2000 N/m. The combined mass moment of inertia of all the rotating components about point O is 0.40 kg·m2. The swing is timed perfectly to strike a 145-gram baseball travelling with a speed of V0 = 10 m/s at a distance of h = 0.7 m away from point O. Knowing that the coefficient of restitution between the bat and ball is 0.59, determine the velocity of the baseball immediately after the impact. Assume that the ball is travelling primarily in the horizontal plane and that its spin is negligible.[20] A crane that is 10 meters long is rotating (while loaded), at 1 radians/sec. It is stopped instantly (in 0.1 radian) in the position shown. Due to momentum the load continues to swing. Ignoring the deflection of the crane for this problem. (list all assumptions). The load is 750 lbs. a) The weight of the 10 m crane boom is 3000 lb and the mass moment of inertia is 80 lb ft s^2 about the centroid. Using the parallel axis theory find the mass moment of inertia around the point of rotation. Parallel axis theory can be found in appendix B formula B.6 (pg A9). b) Determine the maximum VERTICAL distance through which the load will swing. (Use the principle of work and energy with the work done by the weight. Two positions needed). c) What is the normal acceleration of the weight immediately after the crane stops (magnitude and direction)? d) What is the maximum energy that can be transmitted back to the crane (boom and load)? e) What forces and moments are there on the boom at the point…