The velocity and pressure at the entrance to a horizontal pipe are 1 m/s and 120 kPa respectively The velocity andpressure at the exit of the pipe are 1.8 m/s and 100 kPa respectively. What is the head loss (h) between the entry andexit of the pipe?1.81 ma.192 mb.2.14 m2.03 mOd.The velocity and pressure at the entrance to a horizontal pipe are 0.7 m/s and 101040 Pa respectively. The velocity atthe exit of the pipe is 1.6 m/s. What is the pressure at the exit of the pipe?100 kPaO a99.52 kPa101.26 kPaO c.102.57 kPad.

Question 1) Assuming that fluid flowing is water , then the density d will be 1000 kg/m³ Now, P1=…

The velocity and pressure at the entrance to a horizontal pipe are 1 m/s and 120 kPa respectively. The velocity and pressure at the exit of the pipe are 1.8 m/s and 100 kPa respectively. What is the head loss (h) between the entry and exit of the pipe? 1.81 m a. 1 92 m 2.14 m 2.03 m d.

The velocity and pressure at the entrance to a horizontal pipe are 1 m/s and 120 kPa respectively. The velocity and pressure at the exit of the pipe are 1.8 m/s and 100 kPa respectively. What is the head loss (h) between the entry and exit of the pipe? 1.81 m a. 1 92 m 2.14 m 2.03 m d.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2. A pump is used to move water (p = 1000 kg/m³) from a lake into a large tank as shown below. The…

Q: Q1/Water. p=1,94 slugs/ft and v=0.000011 ft/s. is pumped between two reservoirs at 0.2 ft's through…

Q: A pump is installed to deliver water from a reservoir of surface elevation zero, to another of…

A: The flow rate of water is given by calculating losses by pump and head. Now,

Q: Problem Solving: Input your final answer on the space provide. Water flows through the piping…

Q: 10.0 m A 200m 2. An old western town has a water tower to deliver water to the residents. Pictured…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: 3. Determine the flow rate of water, in m3/s, at 5 C though the piping system as shown in the…

Q: 7.1 MHIS the total head at inlet and h is the head lost due to friction, efficiency of power…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The valve in a piping system causes a 3.1 m head loss. If the velocity of the flow is 4 m/s, the…

A: Give Data: Head loss in the pipe is: He=3.1 m The velocity of the flow is: v = 4 m/s.

Q: The water is flowing through a pipe having diameters 45 cm and 15 cm at sections tand 2…

A: Given data diameter at section 1 (d1) = 45 cm diameter at section 2 (d2) = 15 cm discharge rate…

Q: A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.81…

Q: For oil flow through a pipe, velocity increases O 1, with decrease in area of cross section O 2.…

A: Option : With decrease in area of cross section

Q: Water flows downwards in a vertical pipeline of gradually varying section from point 1 to point 2,…

Q: Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine…

Q: If the difference between the total pressure and static pressure in an air duct is measured by a…

Q: 5.9.5. Factory tests indicated that a cavitation parameter for a particular pump is o = 0.075. The…

A: Given: Cavitation parameter for the pump→σ=0.075 Pressure at the sea level→Patm=101.325 KPa…

Q: Q2: Liquid water at 20°C flows straight up 30 m. 1- How much power pump is needed if the mass flow…

Q: In a hydroelectric power palnt, water flows from an elevation of 400 ft to a turbine, where electric…

Q: Q2- Water ( p= 990 kg/m' & u= 0.001 pa.s) is pumping from a water tank to water injection well with…

Q: 1. A pipe carrying oil of specific gravity of 0.877 changes in size from 150 mm at section 1 and 450…

A: GivenS.G=0.877d1=150mmd2=450mmZ2=3.6mP1=90kPaP2=60kPaQ=150L/s=0.150 m3/s

Q: o Consta

A: The sum of potential energy, kinetic energy, and pressure energy per unit weight of the fluid is…

Q: Figure 2 is a schematic of a pumped-storage system. How much power must be supplied to the water by…

Q: Show in Figure 1 is the water flow system. The velocity head difference is = 2.0m. Volume flow rate…

A: Given data as per the question velocity head =2 m volume flow rate =0.5 m3/s h1 =1 m h2 =2 m hA = 3…

Q: Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of…

Q: The power transmitted through a pipe is (where Y =Specific weight in N/m3, (Q = Discharge in m3/s,…

A: Power transmitted through a pipe, Power=YQ(H-hf) Y is the specific weight (N/m3) hf is the head…

Q: (P. = 850 kg/m³, µ = 2.33 kg/ms, Patm = 101.325 KN/m²) oil 1 m = 13600 kg/m³) mercury Oil ball valve…

A: Given: The flow rate inside the tank, Q = 0.03 m^3/s The outside diameter of 4in scheduled 40 pipe,…

Q: Find the mean velocity in pipe 4 (the answer should be negative if the flow out of the pipa). U, =…

Q: The head loss between points (1) and (2) in the figure shown is 0.3 m. Determine the water mass flow…

Q: Water at 40 C flows from a storage tank through a 270 m of DN100 Schedule 40 steel pipe, as shown…

A: Find the hight of water in the tank

Q: Q2: Liquid water at 20°C flows straight up 30 m. 1- How much power pump is needed if the mass flow…

Q: 6. Water flowing through a pipe with a flow rate of 2.2 m3/s and a pressure of 85 kPa. Determine the…

A: Given data: The initial diameter of the pipe is d1 = 1 mThe initial area of the pipe is A1 = (π/4) x…

Q: A 28-in pump is used to deliver water from a lower reservoir to a higher reservoir . The total…

A: Given:d=10 inL=62 ftf=0.022H=365-0.04718Q2

Q: Water flows through the piping junction, entering section 1 at 20 US gallons/min (1 US gal = 3.78…

A: Given data: Q1=20 US gallons/min=12.62×10-4 m3/sv2=2.5 m/sdh=1 mm Need to determine the exit…

Q: In an annular section made of commercial steel pipe with an outer diameter of 13.78 inches inside a…

A: Given data Annular section with Outer Diameter = 23.62 inch = 0.59995 m Inner Diameter = 13.78 inch…

Q: 3. Water is pumped through three pipes in series. Compute the discharge if the power delivered to…

Q: Pressure drop between two sections of a unifrom pipe carrying water is 9.81 kPa. Then the head loss…

Q: Show that the kinetic energy of oil flowing through a pipe is 1.2961 ft-lbf/s given the folowwing:…

Q: 8.59 Two tanks A and B, of constant cross-sectiona! area of 10 m² and 2.5 m², respectively, are…

Q: QUESTION 3 A closed tank partially filled with water discharges through an orifice of 12.5 mm…

Q: Two reservoirs, A and B having elevations 250 m and 100 m, respectively, are connected by a 250-mm…

A: For solution refer below images.

Q: A pipeline has the following data at its two section A and B Item Section - A Section - B Diameter…

A: water flowing through point B to A at point B, D2 =0.45m, Z2 =16m, P2 =30KPa, α2 =1.25 at point A,…

Q: The head loss between points (1) and (2) in the figure shown is 0.3 m. Determine the water mass flow…

A: To find: The mass flow rate. Given: The head loss between 1 and 2 is h12=0.3 m. The water density is…

Q: Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, and pipe 3, with the length…

Q: 33. A pipe has a diameter of 20 cm at section 1 and 6 cm diameter at section 2, as shown. If h = 8…

A: Given that, Diameter of pipe at section 1, d1=20 cm,Diameter of pipe at section 2, d2=6 cm,Pressure…

Q: An induced draft fan handles 63,500 cfm in of flue gas with a gas constant of 51.5116 ft-lb / lb-R…

A: Given data, Volume flow rate, Q = 63500 ft3/min Static pressure, Ps = 4 in water Discharge duct…

Q: If the difference between the total pressure and static pressure in an air duct is measured by a…

Q: Water at 70°F flows by gravity from a large reservoir at a high elevation to a smaller one through a…

A: The density of the water is 62.428 lbm/ft3. The dynamic viscosity of the water is 1.307×10-3…

Q: Pipe Outlet from Reservoir, Local or Minor Head Loss Coefficient, Køutler=0.64 Elbow Local or Minor…

A: Given data: The Pipe outlet from the reservoir, local, or minor head loss coefficient is Koutlet=…

Q: what is the flow velocity in m/s?

Q: 04: Three pipes of diameters 300 mm, 200 mm and 400 mm and lengths 450 m, 255 m and 315 m,…

A: Given, Pipe Diameter (m) Length (m) Friction coefficient 1 0.3 450 0.0075 2 0.2 255 0.0078…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

The velocity and pressure at the entrance to a horizontal pipe are 1 m/s and 120 kPa respectively The velocity and
pressure at the exit of the pipe are 1.8 m/s and 100 kPa respectively. What is the head loss (h) between the entry and
exit of the pipe?
1.81 m
a.
192 m
b.
2.14 m
2.03 m
Od.
The velocity and pressure at the entrance to a horizontal pipe are 0.7 m/s and 101040 Pa respectively. The velocity at
the exit of the pipe is 1.6 m/s. What is the pressure at the exit of the pipe?
100 kPa
O a
99.52 kPa
101.26 kPa
O c.
102.57 kPa
d.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The pressure in a section of a horizontal pipe of diameter d1 = 2.0 cm is p1 = 142 kPa. The water flows through the pipe at a volumetric flow rate V = 2.8 L/s. If the pressure at a certain point is reduced to p2 = 42.6 kPa, due to a throttling of a pipe section, what should the diameter d2 of the throttling section be? Consider the density of water ρ = 1.0 g/cm3. Choose the correct option:
At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is discharged into the atmosphere. The water level is 2 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) and the atmospheric pressure is 100 KPA. Determine the initial rate of water discharge (volumetric flow rate) from the tank, neglecting the effects of friction.
Determine the head loss due to friction of an oil of specific gravity 0.77 and viscosity 0.85 poise is flowing through a pipe at the rate of 3.7 m/s. Assume the pipe diameter as 29 cm and the length of the pipe as 5618 cm. Oil Density (in kg/m3) Reynold's Number - Co-efficient of friction - Head loss due to friction
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
A fan draws 1.42 m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan mechanical is 70% and air is measured at 25 0C and 760 mmHg. Using p water formulaPw=
A fluid flows at 455 m3 per min inside a rectangular duct, whose cross-section has a length of 150 cm and width of 85 cm. What is the average velocity of the flow in m/s ?
Show that the kinetic energy of oil flowing through a pipe is 1.2961 ft-lbf/s given the folowwing: diameter of pipe = 2 in Flow rate = 40 gal/min SG = 0.90 water density = 62.3 lb/ft3
A fan draws 2.42 m^3 per second of air at a static pressure of 2.54 cm water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency IN PERCENT if total fan mechanical is 75 percent and air is measured at 25 deg. Celsius and 760 mm Hg.
Air is flowing in a circular duct. The air flow rate is Q=2000 ft3/min. The diameter of the duct is D=14 in. (2) Determine the friction loss per 100 ft, hL_________inH2O
The friction factor in the plastic pipes for the piping system, which is shown in the figure, The diameter of the orifice located lower section of upper reservoir is 56,2 mm. The length and diameter of the pipe are 800cm and 30mm respectively. The kinematic viscosity and density of water 0.00000162 m2/s and 1000 kg/m3 respectively. Neglecting all the minor head losses and assuming that the system is operating at steady state. Determine and Solve the problem by making the necessary assumptions and drawing the schematic figure. i-volumetric flow rate through the pipe, ii-The head delivered by the pump iii- the power required by the pump, if the pump efficiency is 76,2% percent. (a=6 and b=2on the figure)
A pump is being used to transport a liquid food product (density p=1000kg/m^3, viscosity 0.001 Pa s) from holding tank to filling a machine at a mass flow rate of 2 kg/s. The liquid level in the holding tank is 10 m above the pump, and the filling machine is 5 m above the pump. There is 100 m of 2-in nominal diamter sanitary pipe between the holding tank and the filling machine, wiht one open globe valve and four regular 90° flanged elbows in the system. Within the system, there is a heat exchange which causes 100 kPa of pressure drop due to friction. The holding tank is open to atmosphere, and filling machine is running at a pressure of 1.5 atm. The diamter of the filling machine pipe is 3cm. A: What is the volume flow rate of the system? B: What is the diamete of the pipe? C: What is the average velocity inside the pipe? D: What is the reynolds number of the flow in the pipe? E: What is the flowing type?
A horizontal water pipe diameter 15 cm converges to 7.5 cm diameter. If the pressures at the two sections are 4 kg/cm2, and 1.5 kg/cm2 respectively, calculate the flow rate of water.