The vertical links (at BD and two at CE) has an thickness = 9.9 and width = 27.2 mm uniform rectangular crosssection. The thickness of the member ABC is 5.4 mm. The diameter of the pin is 7.7 mm. Determine the bearingstress (in MPa) in the (a) link BD at B and (b) member ABC at B, if the load is 8.5 N. Choose the correct options,in each option the answer has been rounded off to two places.0.4 m0.25 m0.2 mPBAO a. Bearing stress in member BD is =0.09 MPaO b. Bearing stress in member BD is =0.18 MPaO c. Bearing stress in member BD is =0.03 MPaO d. Bearing stress in member BD is =0.26 MPaO e. Bearing stress in member ABC at B is =0.33 MPaf. Bearing stress in member ABC at B is =0.17 MPaO g. Bearing stress in member ABC at B is =0.18 MPaO h. Bearing stress in member ABC at B is =0.09 MPa

bearing stress in BD member load at BD section will be remain 8.5N and diameter of the pin is 7.7 mm…

The vertical links (at BD and two at CE) has an thickness = 9.9 and width = 27.2 mm uniform rectangular cross section. The thickness of the member ABC is 5.4 mm. The diameter of the pin is 7.7 mm. Determine the bearing stress (in MPa) in the (a) link BD at B and (b) member ABC at B, if the load is 8.5 N. Choose the correct options, in each option the answer has been rounded off to two places.

The vertical links (at BD and two at CE) has an thickness = 9.9 and width = 27.2 mm uniform rectangular cross section. The thickness of the member ABC is 5.4 mm. The diameter of the pin is 7.7 mm. Determine the bearing stress (in MPa) in the (a) link BD at B and (b) member ABC at B, if the load is 8.5 N. Choose the correct options, in each option the answer has been rounded off to two places.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.5.2P

See similar textbooks

Similar questions

4-47. The support consists of a solid red brass C83400 post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. A 0.25 m = 1 mm 60 mm 80 mm Prob. 4-47 -10 mm
The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120KN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel to be used, the maximum allowable stresses are: o = 180 MPa, t = 120 MPa, op = 380 MPa. Design the tie bar by determining the required values of: a. the diameter d of the bolt, b. the dimension b at each end of the bar, c. the dimension h of the bar.
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3,080 mm^2. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.
Six rivets are used in the connection shown in the figure. If both P=50KN, what is the minimum diameter rivet is necessary so as not exceed the 70MPa allow shearing stress? What thickness of plate is required so as not exceed a bearing stress of 140MPA? p= 50 80 mm 80 mm 100 mm
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
Determine the a) normal stress in rod (1), b) the shear stress in pin B and the shear stress in pin A given the following properties of the structure. The tie rod at 1 is 10 mm in diameter. Pin Pin Connection Diameter SET e a b h Connection Type at B & D of pins Type at A A 1300 N 45° 600 250 450 Double Single Shear 12 mm mm mm mm shear D (1) C b
An 8 mm diameter pin is used at A, and 12 mm diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P. Top view 200 mm +180 mm 12 mm 8 mm B B A B 20 mm +8 mm 8 mm OD 12 mm -- - Front view Side view
The bolted connection is subjected to a tensile force of P. The diameter of the bolt is d=60 mm. if P=200kPa. Determine the average shear stress (MPa) in the bolt.
A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. o a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN Pe
ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70MPa for shear in rivet and 140MPa for bearing stress due to the rivets. How many 19-mm diameter rivets are required to fasten the said members to the gusset plate? K.R.R.P. wwwwwwww 00 400 4m B 3m C 96KN 4m 6m 200KN E Am 3m F 96KN 4m H DETAIL OF JOINT B 75X75X6 mm ------------- · ET---- I 14 mm thick GUSSET PLATE P BC 75X75X13 mm P BE
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co