10.32 Water at 20°C flows through a 3 cm ID smooth brass tubeat a rate of 0.002 m³/s. What is ƒ for this flow?10.33 Water (10°C) flows through a 25 cm smooth pipe at a rateof 0.05 m³ /s. What is the resistance coefficient f?10.52 A plastic siphon hose of length 7 m is used to drain water(15°C) out of a tank. For a flow rate of 1.5 L/s, what hose diam-eter is needed? Use H = 5 m and h = 0.5 m. Assume all headloss occurs in the tube.- Siphon hosediameter DhHWater(T = 15°C)

Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Answered: 10.32 Water at 20°C flows through a 3…

Engineering

Mechanical Engineering

10.32 Water at 20°C flows through a 3 cm ID smooth brass tube at a rate of 0.002 m³/s. What is ƒ for this flow?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows naturally from a tank A located at 20 m above the ground level , to a ground leveltank B . The connecting pipeline between tank A and tank B has an equialent loss coefficient of K .Determine the flow rate Q= ? ( USE g= 10 m 2/s) Note that K0,5 : square root of K. ANSWER: 20 / K0,5 m3/s
A long 0.3 m pipeline laid between two reservoirs carries a flowrate of 0.14 m3/s ofwater. A parallel pipe of the same friction factor is laid beside this one. Calculate the approximatediameter of the second pipe if it is to carry 0.28 m3/s
Determine the flow rate in pounds per hour of water at 68Â°F through a 1000-ft length of horizontal 8-in schedule 40 steel pipe (internal diameter 0.7981 in) under a pressure difference of 3.00 psi. k/D = 2.3x10^4.
6. A 6 250 m long, 914 mm (inside diameter) cast iron pipeline connects an upstream reservoir (water surface elevation 521.3 m) to a downstream reservoir (water surface elevation 512.3 m). A discharge valve at the downstream end is used to control flow; when this valve is fully open, the measured discharge in the pipeline is 840 L/s under the naturally available head difference. (a) Assuming fully developed turbulent flow and that all other local losses are negligible, estimate the loss coefficient k for the fully open valve.(b) Because of increasing urban development, the flow under the natural head difference is considered to be inadequate and it is proposed to increase this flow with pumping. The head-capacity curve for thepump can be approximated by the equation H = 8 – 3.5Q2 in which H is the total dynamic head on the pump (in m) and Q is the discharge (in m3/s). What is the discharge that can now be obtained from the system where the pump is installed at a cross-section of the…
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. the total length and diameter of the sunction and discharge pipe are 500 mm,1500 m and 300 mm, 1000 m respectively. assumme a head lose of 2 meters per 100 m length of the sunction pipe and 3m per 100 m length of the discharge pipe. what is the required horsepower of the pump?
On a circular conduit there are different diameters: diameter D1 = 2 m, changes into D2 = 3 m. The velocity in the entrance profile was measured: v1 = 3 m/s. Calculate the discharge and mean velocity at the outlet profile (see figure below). Determine also type of flow in both conduit profiles (whether the flow is laminar or turbulent) – temperature of water T = 12° C. (use Reynold’s number Re), For laminar flow: Re<2320, For turbulent flow Re>2320, Kinematic viscosity of water of 12°C, v is equal to 1,24 10^-6 m2/s.
P7.) A pipe system, connecting two reservoirs whose difference in water surface elevation is 13 m, consists of 320 m of 600 mm diameter pipe (pipe 1), branching into 640 m of 300 mm diameter pipe (pipe 2) and 640 m of 450 mm diameter pipe (pipe 3) in parallel, which join again to a single 600 mm diameter line 1300 m long (pipe 3). Assuming f = 0.032 for all pipes, determine the flow rate in each pipe. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
A 10 in discharge pipe is attached to a certain storage. The head loss from the surface to the discharge is 8 ft. What is the discharge flow rate in ft^3/s? a. 11.58 b. 4.98 c. 8.41 d. 29.15
In an annular section made of commercial steel pipe with an outer diameter or 13.78 inches inside a commercial steel pipe with an inner diameter of 23.62 inches carries a water flowrate of 600L/sec. The total length of the section is 10m. What is the frictional loss in meters of water at a temperature of 68o F?
water at ambient temperature flows through a horizontal tube (surface roughness 0.15mm) of diameter (10 square root 8 mm) with a pressure drop (pressure gradient) of (1000 square root 8) n/m3. Calculate using trial and error method (use at least four digits in your calculations). a) the friction factor, b) the average velocity c) the volumetric flow rate d) the mass flow rate e) the Reynolds number. Characterize the flow.
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m.The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? **provide complete solution using bernoullis equation..provide illustration with labels like datum line and such** Show all formula derivation
Considering pipe loss only, how much head is required to deliver 0.222 m³/s of heavy fuel oil at 38°C through 914 m of new cast iron pipe, 300 mm inside diameter? Use ε=0.00024 m. (ANSWER MUST BE = 41 m)