The wheel is made from a 5-kg thin ring and two 2-kg slender rods. If the torsional spring attached to the wheel's center has a stiffness k = 2 N*m/rad, and the wheel is rotated until the torque M = 25 N·m is developed, determine the maximum angular velocity of the wheel if it is released from rest. 0.5 m M

The wheel is made from a 5-kg thin ring and two 2-kg slender rods. If the torsional spring attached to the wheel's center has a stiffness k = 2 N*m/rad, and the wheel is rotated until the torque M = 25 N·m is developed, determine the maximum angular velocity of the wheel if it is released from rest. 0.5 m M

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 75 kg wheel has a radius of gyration about its mass centreof kG=400mm. If it is subjected to a torque of M=150 N.m,determine:a. The angular acceleration of the wheel,b. The linear acceleration of the mass centrec. The created frictional force at the point of contact.The coefficient of static friction between the wheel and theground is S=0.3.Hint: Assume no slipping occurs at star, and verify I at the end.
The 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μk = 0.2. Neglect the mass of the cord Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μkμk = 0.2. Neglect the mass of the Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
When the 100-lb block is at h = 3 ft above the cylindrical post and spring assembly, it has a speed of = 20 ft>s. If the post is made of 2014-T6 aluminum and the spring has the stiffness of k = 250 kip>in., determine therequired minimum diameter d of the post to the nearest 1/8 in. so that it will not yield when it is struck by the block
The automobile has a mass of 2 Mg and center of mass at G. Determine the towing force F required to move the car if the back brakes are locked and the front wheels are free to roll. Take us=0.3.
18-54 The slender 6 kg bar AB is horizontal and at rest and the spring is unstretched. Determine the stiffness K of the spring so that the motion of the bar is momentarily stopped when it has rotated clock wise after being released.
The trailer with its load has a mass of 200 kg and a center of mass at G. If it is subjected to a horizontal force of P = 1000 N, determine the trailer’s acceleration and the normal force on the pair of wheels at A and at B. The wheels are free to roll and have negligible mass.
A force was applied to a 50 kg wheel as shown in the figure. If the wheel starts to rest without slipping Determine the angular acceleration ε, the wheel pressure on the ground N and the rotational speed of the wheel n after 10 revolutions, if the rolling friction coefficient f = 0.1. Take the radius of inertia of the wheel equal to 0.3 m.
The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of gravity, kG = 250 mm. Whereas there is no slip, determine the angular velocity of the rotates after it rotates 90 ° clockwise from illustrated position. The AB spring has a constant stiffness k = 100 N / m and a length in the undisturbed situation of 500 mm. Consider that the wheel is initially at rest.
6/40 If the frictional moment at the pivot O is 2 N+m, de- termine the angular acceleration of the grooved drum, which has a mass of 8 kg and a radius of gyra- tion kg = 225 mm. 200 mm kg 12kg
The dynamic system is initially at rest. The rod has a mass of m=0.5kg and a length of L=1m. The CG of the rod is located at G, and the rod is rotated about the point O, a distance, h=0.25m, away from point G. At the time of releasing find a. Acceleration at the CG (point G) b. Reaction at O (Use moment of inertia of the rod I= mL2/12)