The wood specimen is subjected to the pull of P =15 kN in a tension testing machine. If the allowable normal stress for the wood is 11 MPa, allowable bearing stress is 13 MPa and the allowable shear stress is 1.2 MPa, determine the required dimensions t and c so that the specimen reaches these stresses simultaneously. The specimen has a width of 25 mm. -b 4 P

The wood specimen is subjected to the pull of P =15 kN in a tension testing machine. If the allowable normal stress for the wood is 11 MPa, allowable bearing stress is 13 MPa and the allowable shear stress is 1.2 MPa, determine the required dimensions t and c so that the specimen reaches these stresses simultaneously. The specimen has a width of 25 mm. -b 4 P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The boards for a concrete form are to be bent into a circular shape having an inside radius of 10 m. What maximum thickness can be used for the boards if the normal stress is not to exceed 7 MPa? Assume that the modulus of elasticity of the wood is 12 GPa.
A pair of wood components having a dimension of 100mm X 100mm is joined by means of glue as shown. Determine the maximum axial load F, that most nearly can be subject to the woodpost without exceeding a maximum shear stress of 1650 KPa parallel to the cross section in kN.
Therectangular wood beam is loaded asshown in the figure. Solve thefollowing:What is the maximum bendingstress in the beam?What is the maximum shear stress in the beam?
A piece of wood with a triangular cross section contains a rubberized joint to aangle θ with the vertical. The stress that the wood resists in tension is 20 MPa, the rubber resists10 MPa in tension and 12 MPa in shear. If θ = 60, determine the maximum load P.
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION, 20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE X DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF Px=3 (COMPRESSION), Py=6 (TENSION) AND Pz=9 (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.
Determine the cracking moment Mcr for the beam depicted in Fig. 6.85. Assume normal-weight concrete, and Grade 60 reinforcing bars. Calculate the bending stresses in the extreme fibers of the cross-section for a service-load bending moment of 90 ft kips.
A third-point bending test was performed on a 100 * 150 mm wood lumber according to ASTM D198 procedure with a span of 1.8 m and the 150 mm side is positioned vertically. A strain gauge is glued at the center point between the supports. The strain gauge is zeroed at the start of the test when the force is zero. A strain of 0.00456 is measured when the combined load is 6.672 kN and the load–strain curve is in the linear range. Determine the flexural modulus of elasticity. If the maximum combined load on both loading bearings was 22.722 kN, calculate the modulus of rupture.
A reinforced concrete beam with a width of 8 in., a depth of 24 in. is poured monolithically with a 6-in.-thick slab as shown in the cross section provided below. The beam is reinforced with 3 # 8 steel reinforcing bars Grade 60 with a distance from the top of the slab to the centroid of the reinforcement of 27 in. (cover of 3.0 in.). If the concrete has a 28-day compressive strength of 4000 psi , calculate: The cracking moment (Mcr) The nominal moment capacity (Mn) The strain in the reinforcement at the time of concrete crushing (Ecu=0.003) The strength reduction factor (phi) The resistance moment capacity of the beam (Mr) Check the minimum area of reinforcement (As min)
Given the following properties of beam: b = 250 mm d = 325 mm h = 400 mm a) Assuming the concrete is uncracked, compute the bending stresses in the extreme fibers of the beam at M = 150 kN-m b) Determine the cracking moment for the section if f'c = 28 MPa c) Compute the flexural stresses in the concrete and steel of the beam using the transformed-area method at M = 150 kN-m, n = 8, and reinforced with 4-16 mm diameter tension bars. NOTE: Please answer the question correctly, if you are not sure about the answer(s) please skip the question. Please box the final answer(s) Thank you
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. STRENGTH OF MATERIALS A rectangular block has dimensions of 3 in, 4 in, and 5 in along the x-, y-, and z-axes, respectively. The block is subjected to triaxial loading of three uniformly distributed loadings of 100 kips (C), 120 kips (T), and 140 kips (C) along the x-, y-, and z-axes, respectively. If the strain along the x-axis and the z-axis are 0.00071 (C) and 0.00189 (T), respectively, determine the Poisson’s ratio and the modulus of elasticity of the material. Also, what is the change in volume of the material?
For parallel nonpresstressed reinforcement in a horizontal layer, clear spacing shall be at least the greatest of ____ db and (4/3 max diameter of aggregates) a) 25mmb) 50mmc) 10mmd) 40mm
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION,20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE XDIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF AUNIFORMLY DISTRIBUTED FORCE OF Px=3kN (COMPRESSION), Py=4kN(TENSION) AND Pz=7kN (COMPRESSION) IN THE X, Y AND Z DIRECTIONSRESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa,DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSODETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THEWOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.