The x,y, and z edges of a rectangular parallelepiped are 1, 2, and 4 respectively. If the diagonal OP drawn from the origin represents a 60-N force. Determine the x,y, and z components of the force. Express the force as a vector in terms of the unit vectors ij, and k.

The x,y, and z edges of a rectangular parallelepiped are 1, 2, and 4 respectively. If the diagonal OP drawn from the origin represents a 60-N force. Determine the x,y, and z components of the force. Express the force as a vector in terms of the unit vectors ij, and k.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.48P: The pole OB is subjected to the 6004b force at B. Determine (a) the rectangular components of the...

See similar textbooks

Related questions

Q: A temperature probe is used to measure the temperature of gas flowing through a pipe. The gas temper...

Q: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto ...

Q: dr +e (x - 1) +x = 0 dt dt?

A: The van der pol's equaton- d2xdt2+ε(x2-1)x'+x=0this ODE subsidiary is a self energized ...

Q: Q.7/determine the angle O so that the resultant force directed horizontally to the right. *

Q: A SOUnd w avet ravels froma ir kg(smiz 413=RZ) teali quidof density of KG(M3950) and quickly Socend ...

Q: In a Rankine cycle, steam leaves the boiler and enters the turbine at 4 MPa and 400◦C. The condenser...

Q: (S) Sonic wave of air kg) "M2s 413 = Z (to a longer liquid KG (M3 950) and quickly sound) 's cm 7500...

A: Given Data,Zair=413 kg m2/sϕL=950 kgm2VL=750 m/s

Q: An aluminum pole for a street light weighs4600 N and supports an arm that weighs 660 N (seefigure). ...

A: Here now assume it as a cantilever beam now find the reactions at A Using the equilibrium equation ...

Q: A raft is constructed of wood having a density of 600 kg/m³. Its surface area is 5.7 m², and its vol...

Q: The following data refer to a laboratory experiment with rope brake Diameter of the flywheel = 1 m; ...

A: We have Diameter of drum, D=1 m Diameter of rope, d=10 mm=0.01 m Speed of engine, N=200 rpm

Q: A hydraulic jack has a 2-inch diameter input piston and a 2-inch diameter output piston. If a 300 lb...

Q: 1. Calculate the composition of a lin (Sn)/ lead (Pb) alloy Lhat has the lowest melting point. Plot ...

A: FIBER REINFORCEMENT 1.The properties of fiber reinforcement composites depend upon the following fac...

Q: A 4.0 kg mass, ml, hangs from a rope that runs over a massless frictionless pulley and is connected ...

Q: 1. A 150 inch long aluminum bar is subjected to a tensile stress of 25000 psi. Find the elongation. ...

Q: 1. If A(-4,-6), B(3,–3), C(5,7), and D(x,y) are vertices of a parallelogram ABCDA, determine the coo...

Q: Question 63 The dimensions of a solid rectangular beam sections (assume solid and homogeneous) are s...

Q: 1. What is the main function of a flywheel in an engine? 2. In what way does a flywheel differ from ...

Q: A motor operates according to the cycle shown in the figure below. In this cycle processes 1➝2 and 3...

Q: An automobile starting from rest speeds up to 12 m/s with a constant acceleration of 1.2 m/s2. Runs ...

A: GivenV1=0 m/sV2=12m/sa=1.2m/s2V3=12m/sV4=0m/sa=-1.5m/s2d=390m

Q: The truss is supported by a pin connection at A and a roller at E. It is loaded as shown. Use the pi...

Q: For the mechanism shown in the figure, find the accelerations of the connecting rod at its center of...

Q: 13. A gas mixture consists of 5 kg of O2, 8 kg of N2, and 10 kg of CO2. Determine (a) the mole fract...

A: Given Datamo2=5kgmN2=8kgmCO2=10kgRg=8.314kJ/kmol.K [taken]

Q: Water flows inside a pipe as shown in Fig. (3). At the lower point, the pipe diameter is 5 cm and pr...

Q: Show complete solution: A vessel of volume V, with a constant cross-sectional area of A and a height...

A: given; corss sectinal area=Ainitial height=Hvessel volume=Vdensity of fluid=ρ

Q: A bus at rest starts moving with an acceleration of 0.1 m/s² . What will be its speed after 2 minute...

A: Given, Initial velocity of bus = u = 0 m/s (As bus starts from rest) Acceleration of bus = a = 0.1 m...

Q: a standard vapor compression refrigeration system uses ammonia as refrigerant the amount of the evap...

Q: VA = 30 m/s 4. The pitching machine is adjusted so that the baseball is launched with a speed of VA ...

Q: A 4.0 kg mass, ml, hangs from a rope that runs over a massless frictionless pulley and is connected ...

Q: Consider a system of nonrelativistic electrons in a white dwarf star at a temperature of 10^9 K. Ver...

A: Write the formula for the density of a non-relativistic electron in a degenerate system. ρ=kμe5/310-...

Q: A pelton wheel is supplied with water under a head of 100 m at the rate 1000 litres/s. The bucket de...

A: Given that, H=100 m; Q=1000 L/s=10001000=1 m3/s ;ϕ=180-160=20° ;u=20 m/s

Q: () The Surface tension of water in contact with air at 23C is given as 745x10-4 N/m. The pressure in...

Q: Your steam has a Data of 5.32 MPa and 325 ℃. Find v, u, h and s.

Q: A refrigerating system operates on the reversed Carnot cycle. The higher temperature of the refriger...

A: Given data Refrigeration system works on reversed Carnot Cycle.Higher Temperature of the refrigerant...

Q: Determine the length of the fillet weld lap joint shown in the figure below. The weld has to resist ...

Q: In the figure shown, the load needs to be raised 28 ft. Noting that Gear A is initially at rest and ...

A: given; speed (N)=120rpmat time (t)=5s

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

A: Here we have 0.01 ft per 100 ft pipe lengthSo head loss for 1 ft=0.011000 ft

Q: A 4.0 kg mass, ml, hangs from a rope that runs over a massless frictionless pulley and is connected ...

Q: Where are the application of slider crank mechanism? Answer at least five applications

A: Slider Crank Mechanism is most widely used mechanism, they are used in a number of places like, 1. E...

Q: The truss is supported by a pin connection at A and a roller at E. It is loaded as shown. Use the pi...

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN GIVEN MEMBER

Q: A bar with a circular cross section having twodifferent diameters d and 2d is shown in the figure.Th...

A: When an elastic body is loaded it undergoes deformation i.e its dimensions change and when it is rel...

Q: thapter 2, Problem 2/088 n exhaust system for a pickup truck is shown in the figure. The weights Wh,...

Q: A buildup of brake dust and dirt between the lining and the drum is the most common cause of a. a. ...

A: A buildup of brake dust and dirt between the lining and the drum is the most common cause of a Score...

Q: Determine the pumping power (in kW) required, if water at 30°C is flowing through a pipe length of 1...

Q: Determine the total force and location of centre of pressure on one face of the plate shown in Fig. ...

A: Total force, F=ρgAh¯h¯=2+22=3 mF=0.9×1000 kg/m39.81 m/s2π422-123F=62408.52 N,

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =...

Q: Diameter = 100m Bench Height = 10m Bench Width = 5m Bench Slope Angle = 45° a. What is the volumetri...

A: Write the given data. V1=63846.66 m3V1+V2+V3=99745 m3

Q: Problem II. A proposed elevated tank for a certain community has a diameter of 72 inches and a heigh...

A: Solution: Given Data: d = 72 in h = 120 in A = 24.4 in2 γ=62.4 lb/ft3

Q: A carnot engine is working between the temperature range of 227°C and 127°C. If the heat absorbed by...

A: From the given data, Higher temperature in carnot cycle = TH = 227 oC = 500 K Lower temperature in c...

Q: An external load caused tensile stress is imposed along the [001] of a BCC single crystal. The initi...

A: Body-Centered cubic (BCC) is the name given to a kind of iota plan found in nature. A body-focused c...

Q: Find the stress in the rod having a diameter of 20 mm, subjected to 10 kN force. If the material of ...

Question

Need help with this!!

2. The x,y, and z edges of a rectangular parallelepiped are 1,
2, and 4 respectively. If the diagonal OP drawn from the origin
represents a 60-N force. Determine the x,y, and z components
of the force. Express the force as a vector in terms of the unit
vectors ij, and k.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1:

VIEW

Step 2:

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The forces P1=110lb,P2=200lb, and P3=150lb are equivalent to a single force R. Determine (a) the magnitude of R; and (b) the coordinates of the point where the line of action of R crosses the yz-plane.
The force R is the resultant of P and 0. Determine Q and the angle .
The pole OB is subjected to the 6004b force at B. Determine (a) the rectangular components of the force; and (b) the angles between the force vector and the coordinate axes.
Q2) What is the magnitude of F2 and its direction Ø ,when the magnitude of the resultant force acting on the bracket is 600N directed along the positive x axis
A 60 N force acting at 30 east of north and a second 60 N force acting in the direction 60 west of north are concurrent forces. Determine the magnitude and direction of the resultant force
Suppose that F = 570 kN Determine the magnitude of the resultant force.
Determine the magnitude and coordinate direction angles (x, y, z) of the resultant force.
Determine (a) the x, y, and z components of the 450-N force, (b) the angles 0x, 0y, and 0z that the force forms with the coordinate axes.
1. Find the x and y component force of vector A and B. 2. Add F ax + F bx to find the resultant force in the x direction. 3. Add F ay + F by to find the resultant force in the y direction.
Q4/ The ring is subjected to three concurrent and coplanar forces. Express each force acting on the post into its x and y components. As shown in fig. 4). And determine the magnitude and direction of the resultant force. Express the forces as a Cartesian vector
a. summation of force in x axis and y axis b. magnitude of the resultant force c. direction of the resultant force
Express the force F1 and F2 in Cartesian vector form. Determine the magnitude of the resultant force. Determine the coordinate direction angle α, β, and γ of the resultant force.