The y-axis of an x-y positioning table is driven by a stepping motor that is connectedto a leadscrew with a 3:1 gear reduction. The stepping motor has PPR-72 pulse/rev.The leadscrew has a pitch 0.2 in/rev and provides an axis range = 30 in. Determine(a) the required rotational speed of the y-axis stepping motor and (b) thecorresponding pulse train frequency to drive the table in a straight line (incrementalpositioning) from point (20,25) inch to point (4.5,7.5) inch in exactly 30 sec (0.5min).Ignore acceleration.

Given Data as below:Leadscrew gear ratio rg =3:1PPR = 72 pulse/revpitch p= 0.2 in/revaxis range L =…

Answered: The y-axis of an x-y positioning table…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A CNC machine tool table is powered by a servomotor, ball screw, and optical encoder. The ball screw has a pitch = 7.5 mm and is connected to the motor shaft with a gear ratio of 12:1. The optical encoder is connected to the ball screw and generates 200 pulses/rev of the screw. The table must move a distance of 300 mm at a feed rate = 450 mm/min. (a) Determine the pulse count received by the control system to verify that the table has moved exactly 300 mm. Also, what are (b) the pulse rate and (c) motor speed that corresponds to the specified feed rate?
Q6. Gear and Motor selection: For a 50 Hz supply frequency, the motor speed is 50 revolutions per second. What gearbox is required to step this down to 2 rad s−1 at the pulley wheel? What is the maximum torque to be developed by the motor? Round off your answers to one decimal place. -The gear ratio required is ? - The maximum torque to be developed by the motor is Nm ?
The two axes of an x-y positioning table are each driven by a stepping motor connected to a leadscrew with a 10:1 gear reduction. The number of step angles on each stepping motor is 20. Each leadscrew has a pitch = 5.0 mm and provides an axis range = 300.0 mm. There are 16 bits in each binary register used by the controller to store position data for the two axes. What is the control resolution of each axis? What are the required the rotational speeds and corresponding pulse train frequencies of each stepping motor in order to drive the table at 600 mm/min in a straight line from point (25,25) to point (100,150)? Ignore acceleration.
The worktable of a CNC machine tool is driven by a closed-loop positioning system that consists of a servomotor, ball screw, and optical encoder. The screw has 4 threads/in and is coupled directly to the motor shaft (gear ratio = 1:1). The optical encoder generates 180 pulses per motor revolution. The table is programmed to move a distance = 6.0 in at a feed rate = 25.0 in/min. (a) How many pulses are received by the control system to verify that the table has moved the programmed distance? Determine (b) the pulse rate and (c) motor speed that correspond to the specified feed rate.
Simple FM problem ,Solve in 20-30min.
Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal output speed as 725 rpm. Starting with belt linear velocity 4000 ft/min, specify the output sheeve D2 once you specify D1 from last question. D2 = ___ in. Provide write down steps including equations. *** 21.07 and 21.1 were marked incorrect
A stepping motor with 240 step angles is coupled to a leadscrew through a gear reduction of 5:1 (5 rotations of the motor for each rotation of the leadscrew). The leadscrew has 6 threads/in. The worktable driven by the leadscrew must move a distance = 10.00 in at a feed rate of 30.0 in/min. Determine: Number of pulses required to move the table, and The required motor speed and pulse rate to achieve the desired table speed.
A tachometer has a transfer function of 2.5 V/1000 rpm. The tachometer is physically attached to a motor which is also attached to a 10:1 built in gear box; the tach produces 2V. The figure below is to provide a picture of the system, the numbers are different. Find the velocity of the input shaft. Find the velocity of the output shaft.
Design a 20 degree full depth involute profile of a speedr educer to transmit 12 kW of power. Speed of pinion is 1800 rpm speed reduction is 3:2. Assume number of teeth on the pinion is 18 and module of 4 mm.
Find natural frequency
Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal output speed as 725 rpm. Starting with belt linear velocity 4000 ft/min, specify the output sheeve D2 once you specify D1 from last question. D2 = ___ in. Provide write down steps including equations.
An incremental optical encoder coupled to a robot wheel has 2880 slots. Find: a) change in angle when 1200 pulses counts are obtained b) number of pulse counts when the angular change is 5000 degrees

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS