The zero-sequence, positive-sequence and negative-sequence bus impedancematrices for a three bus power system are given as[0.21 0.42 0.55]Zous = j 0.42 0.75 0.64 puLo.55 0.64 0.85][0.36 0.45 0.75]ZBus = ZBus = i 0.45 0.85 0.82 puLo.25 0.82 0.34]Evaluate the per unit fault current and the bus voltages during fault at bus 1, with faultimpedance, Zr given as j0.1 for:a.a three phase fault.a single line-to-ground fault.b.C.a line-to-line fault.

Given data: Zbuso=j0.210.420.550.420.750.640.550.640.85 pu…

The zero-sequence, positive-sequence and negative-sequence bus impedance matrices for a three bus power system are given as [0.21 0.42 0.55] Zous =j 0.42 0.75 0.64 pu Lo.55 0.64 0.85) [0.36 0.45 0.75] Zbus = ZBus = j 0.45 0.85 0.82 pu Lo.25 0.82 0.34] Evaluate the per unit fault current and the bus voltages during fault at bus 1, with fault impedance, Zi given as jo.1 for. a. a three phase fault. b. a single line-to-ground fault. C. a line-to-line fault.

The zero-sequence, positive-sequence and negative-sequence bus impedance matrices for a three bus power system are given as [0.21 0.42 0.55] Zous =j 0.42 0.75 0.64 pu Lo.55 0.64 0.85) [0.36 0.45 0.75] Zbus = ZBus = j 0.45 0.85 0.82 pu Lo.25 0.82 0.34] Evaluate the per unit fault current and the bus voltages during fault at bus 1, with fault impedance, Zi given as jo.1 for. a. a three phase fault. b. a single line-to-ground fault. C. a line-to-line fault.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem 9.42P

See similar textbooks

Similar questions

Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
As shown in Figure 1, a synchronous generator and motor are rated 100MVA, 13.8 kV. Xm" = 0.2 per unit, Xg" = 0.15 per unit, and XT = 0.305 per unit. The synchronous generator is operating at 100 MVA, 0.95 p.f. lagging and at 1.05 per unit voltage when a three-phase short circuit occurs at bus 2. Please use the superposition method to calculate the per-unit values of (a) subtransient generator current (Ig"); (b) subtransient motor current (Im"); and (c) subtransient fault current (If).
A single-line diagram of a four-bus system is shown in fiugre. Equipment ratings and per-unit reactances are given as follows.Machines 1 and 2: 100 MVA 20 kV; X1= X2 = 0.2; X0= 0.04 Xn= 0.05 Transformers T1 and T2: 100 MVA 20Y/345Y kV; X1 = X2 = X0 = 0.08. On a base of 100 MVA and 345 kV in the zone of the transmission line, the series reactances of the transmission line are X1 = X2 = 0.15 and X0=0.5 per unit. (a) Determine the bus impedance matrix for each of the three sequence networks. (b) Assume the system to be operating at nominal system voltage without prefault currents when a bolted single-line-toground fault occurs on phase A at bus 3. Compute the fault current, the current out of phase C of machine 2 during the fault, and the line-toground voltages at the terminals of machine 2 during the fault. Total detailed answer is needed. The figure is attached.
Figure 5 shows a single-line diagram of a three-bus power system. Power flow input data are givenin Tables 1 and 2. (a) Determine the Ybus Matrix (b) Use Gauss-Seidel method to compute V2(1) and V3(1), the phase voltages at bus 2 and 3 after the first iteration. Use zero initial phase angles and 1.0 per-unit initial bus voltage magnitudes.
The one line diagram of a simple three bus power system is shown in figure Each generator is represented by an emf behind the subtraction reactance. All impedances are expressed in per unit on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. Athree phase fault occurs at bus 3 through a fault impedance of Zf=j0.19 per unit. a-using thevenin’s theorem obtain the impedance to the point of fault and the fault current in per unit. b-determine the bus voltage and line currents during fault