There is a long cylinder inside an oven and we are using lumped capacitance method to find the temperature at its extremes. The temperature at the centre of the cylinder is 1000 C, what will be the temperature at its one end where it is away from heat source according to our calculations? not sufficient information more than 1000 C equal to 1000 C less than 1000 C

There is a long cylinder inside an oven and we are using lumped capacitance method to find the temperature at its extremes. The temperature at the centre of the cylinder is 1000 C, what will be the temperature at its one end where it is away from heat source according to our calculations? not sufficient information more than 1000 C equal to 1000 C less than 1000 C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.27P

See similar textbooks

Similar questions

5.10 Experiments have been performed on the temperature distribution in a homogeneous long cylinder (0.1 m diameter, thermal conductivity of 0.2 W/m K) with uniform internal heat generation. By dimensional analysis, determine the relation between the steady-state temperature at the center of the cylinder , the diameter, the thermal conductivity, and the rate of heat generation. Take the temperature at the surface as your datum. What is the equation for the center temperature if the difference between center and surface temperature is when the heat generation is ?
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
A certain material has a thickness of 30 cm and a thermal conductivity of 0.04 W/m- °C. At a particular instant in time, the temperature distribution with x, the distance from the left face, is T = 150x ^ 2 - 30x , where x is in meters. Calculate the heat-flow rates atx x = 0 and x = 30 cm . Is the solid heating up or cooling down?
You have a solid with a semicylindrical shape. One ofthe bases is located in θ = 0 , of area (r 2 - r 1 )L and is maintained at temperature T 0 and the other islocated at θ = π and also of area equal to (r 2 -r 1 )Lhas temperature is equal to Tπ. The conductivityThe thermal temperature of the solid varies linearly with thetemperature from k 0 at T=T 0 to kπ at T=Tπ a. Find the temperature distribution instationary stateb. Find the total heat flux through thesurface at θ = 0.
Find the steady-state temperature distribution in a metalic plate 20 cm by 60 cm if the two adjacent plates are held at 200 degree and the other two sides at zero degree.
Air surrounding a light bulb is moving at 25 m/sec. The surrounding conditions are kept at atmospheric pressure and at temperature 25o C. The light bulb external surface is kept at 140o C. What is the heat transfer rate from the light bulb to the surrounding? Assume the light bulb as a sphere with a diameter of 50 mm.
A solid rod has a temperature profile described by the equation T= 5x+100 (K) and a thermal conductivity of k=10 (W/m*K) What is the heat flux, q?
Hi, can you help me with the following problem? A thermally insulated tank of water 2 m x 2 m, depth 1 m is stirred with a paddle for threehours. If the paddle is driven by a motor whose shaft power is 8 kW determine the rate ofchange of temperature in degrees C per hr and the increase in temperature of the water.The specific heat of water is 4200 J/kgC. Identify a system and start your analysis from anappropriate form of the Fist Law of Thermodynamics
An underwater sonar that maps the ocean bathymetry is encapsulated in a sphere with a diameter of 85 mm. During operation, the sonar generates heat at a rate of 300W. What is the sonar surface temperature when it’s located in a water column where the temperature is 15o C and the water current is 1 m/sec? The sonar was pulled out of the water without turning it off, thus, it was still working. The air temperature was 15o C and the air speed was 3 m/sec. What was the sonar surface temperature? Was there any reason for concern?
Consider a long horizontal pipe with a diameter of 90 mm and emissivity of 0.8 transfers steam at 227°C. Outside of the pipe is air at 27°C and the surroundings of the pipe are also at 27°C. You may assume the temperature of the pipe wall is the same as the temperature of the steam. 1. Find the heat loss per unit length (W/m) for the pipe when the air outside is still. 2. Find the heat loss per unit length (W/m) for the pipe when the wind outside is 8 m/s and blows perpendicularly across the pipe.
Calculate the heat transferred from the cube-shaped iron mass (a = 30 cm) to the environment at 20 ° C with all surfaces at a temperature of 100 ° C. (Assume that the heat is only from the surfaces, the inner parts of the surfaces are insulated.)