C 34. A horizontal cylindrical tube is divided into four parts with the help B two fixed partitions A and B and a movable piston C. The tube and the piston C are made from heat insulating materials whereas the fixed partitions A and B are made from a conducting material. Volume between the fixed partitions A and B is V1 and initial volume between the fixed partition B and piston C is V2. These volumes are filled with an ideal mono-atomic gas at pressure po and temperature To. Outside the piston C, pressure is also po. Quantity AQ of heat is slowly d transferred through the partition A to the gas trapped between the partitions A and B. Find temperatures of the gases on both sides of the partition B and heat transferred through it. Po Po To V2 Ро

C 34. A horizontal cylindrical tube is divided into four parts with the help B two fixed partitions A and B and a movable piston C. The tube and the piston C are made from heat insulating materials whereas the fixed partitions A and B are made from a conducting material. Volume between the fixed partitions A and B is V1 and initial volume between the fixed partition B and piston C is V2. These volumes are filled with an ideal mono-atomic gas at pressure po and temperature To. Outside the piston C, pressure is also po. Quantity AQ of heat is slowly d transferred through the partition A to the gas trapped between the partitions A and B. Find temperatures of the gases on both sides of the partition B and heat transferred through it. Po Po To V2 Ро

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. Steam is held in two compartments separated by a membrane. The total volume is 777 ft3, and the volume ofcompartment B is 280 ft3. The specific volume of the steam in B is 9.5 ft3/lbm. The membrane breaks and theresulting specific volume is 12.75 ft3/lbm. Determine the original specific volume in compartment A in ft3/lbm.
A cylindrical water tank has a height of 8 m and a radius of 2 m. Suppose the water tank is half full of water. Determine the work required to empty the tank by pumping the water to a level 2 m above the top of the tank. Leave the answer in terms of p, g, and pi if necessary.
A man is standing on a board on a frozen lake where there is no friction between the board and the ice surface. Tha man's mass is 2 m and the boaf's mass is 4 m. The board has length L. He walks from 1/5 Lfrom the left end of the board to 1/5 L from the right end of the board. How far and in which direction does the board move during this process?
b) A pipeline bends in the horizontal plane through an angle of 45°shown in Figure 6.Thediameter of the pipe changes from 0.6 m before the bend to 0.4 m after it. Water enters the bend at the rate of 0.5 m3/s with a pressure of 150 x 103N/m2. Assuming that there is no loss of energy.i) Determine pressure at the outlet, P2-ii) Calculate the magnitude and direction of the resultant force exerted on the pipe bend by the water.
A boat having a mass of 80 Mg rests on the bottom of the lake and displaces 11.75 m^3 of water. Since the lifting capacity of the crane is only F = 550 kN, two balloons are attached to the sides of the boat and filled with air. The volume of a sphere is V =4/3πr^3. ρw = 1000 kg/m^3.Determine the smallest radius r of each spherical balloon that is needed to lift the boat. Neglect the mass of air and of the balloon for the calculation required for the lift and What is the mass of air in each balloon if the air and water temperature is 12∘C? The balloons are at an average depth of 20 mm. The gas constant for air is R= 286.9 J/(kg⋅K)
A gas is compressed inside a compressor’s cylinder. Whenthe piston is at its bottom dead center, the gas is initiallyat 10 psig, 65°F, and 10.5 in3. After compression andwhen the piston is at top dead center, the gas is 180°Fand occupies 1.5 in3. What would be the new pressure ofthe gas in psig?
A fluid, contained in a horizontal cylinder fitted with a frictionless leak proof piston, is continuously agitated by means of a stirrer passing through the cylinder cover. The cylinder diameter is 0.40 m. During the stirring process lasting 10 minutes, the piston slowly moves out a distance of 0.485 m against the atmosphere. The net work done by the fluid during the process is 2 kJ. The speed of the electric motor drivingthe stirrer is 840 rpm. Determine the torque in the shaft and the poweroutput of the motor.
A vertical frictionless piston cylinder contains air at a pressure of 300 KPa with atmospheric pressure of 100 KPa. The diameter of the piston is 0.25m, and g = 9.8m/s2. Determine the piston’s mass.
A vertical, frictionless piston–cylinder device contains a gas at 600 kPa. The atmospheric pressure outside is 100 kPa, and the piston area is 30 cm2. Determine the mass of the piston.
For the tank of water shown below, the radius of the circular surface is R=1.0 m, h=1.0m, and the length of the tank is w=2.0 m. Determine (2) the area magnitude whose volume weight is equivalent to the vertical force exerted on the whole curved surfaces_________m2 A. 0.785 B. 4.785 C. 1.57 D. 3.2146
: The tank shown in figure below is partially filled with water. On the top of the water there is compressed air for which the pressure is the same at every point (h1=4m, h=0.4m a=2m, 1=10 kN/m3, 2=136 kN/m3 Determine:a) The pressure, due to the compressed air on the water surface,b) The force on the triangular gate AB,c) The point of application of the hydrostatic force on the gate from the bottom of the tank
A piston (D = 5 cm) is attached to a tank that includes oil (ρ = 850 kg/m3), as shown in the figure below. The pressure within the tank is to be measured by a U-tube attached to the tank. a) Suppose that the piston has negligible weight and the height of the mercury on the right leg of the U-tube (hm) is 15 cm. Determine the vertical distance between the cylinder surface and the mercury on the left leg of the manometer (H). b) Now suppose that the total mass of the piston is 10 kg. Determine the variation in the height of the mercury on the right leg of the U-tube.