thermodynamics Calculate the maximum work that can be achieved from the process where a methane gas, considered to be an ideal gas, initially at 500 K and 10 bar undergoes a process that ultimately changes its pressure to 200 K and atmospheric pressure, which is the same as the temperature and pressure of the surroundings.

thermodynamics Calculate the maximum work that can be achieved from the process where a methane gas, considered to be an ideal gas, initially at 500 K and 10 bar undergoes a process that ultimately changes its pressure to 200 K and atmospheric pressure, which is the same as the temperature and pressure of the surroundings.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

thermodynamics What is the final temperature if an ammonia gas, considered to be an ideal gas, initially at 500 K and 3 bar undergo a process that ultimately changes its pressure to atmospheric pressure undergoes reversible adiabatic expansion?
A cylinder that contains 0.067 kg of carbon dioxide (with molar mass 44 kg/kmol), occupying a volume of 0.022 m3 at 1 bar is compressed reversibly until the pressure is 7.2 bar. If the molar (universal) gas constant as 8.3145 kJ/kmol K, calculate the final temperature (in C) when the process is isothermal.
Determine the change in entropy of an ideal gas with constant heat capacity, CP=3.5R between the following States: P1= 1 bar, T1= 300k; V2= 0.025m³/mol;T2= 500k
During a steady flow process, the pressure of the working substance drops from 100 to 20 psia, the velocity increases from 200 to 1200 fps, the internal energy decreases 25 Btu/lb., and the volume increases from 1 to 6 cu.ft/lb. If the heat transferred is zero, what is the work of 1 lb. of the substance in Btu?
Define reversible work, which is the maximum useful work that can be obtained as a system undergoes a process between two specified states.
A mass of 0.05 kg of carbon dioxide (molar mass 44 kg/ kmol, gamma 1.3), occupying a volume of .03 m3 at 1.025 bar, is compressed reversibly until the pressure is 6.5 bar. Determine the final temperature, the work done on the CO2, and the heat supplied: (1) When a process is isothermal.
a certain stable thermodynamic system is found to warm up when it is adiabatically expanded to lower pressures. show that for this system the entropy must increase upon isothermal compression
An ideal gas, initially at 30°C and 100 kPa, undergoes the following cyclic processes in a closed system: (a) In mechanically reversible processes, it is first compressed adiabatically to 500 kPa, then cooled at a constant pressure of 500 kPa to 30°C, and finally expanded isothermally to its original state. (b) The cycle traverses exactly the same changes of state, but each step is irreversible with an efficiency of 80% compared with the corresponding mechanically reversible process. Note: The initial step can no longer be adiabatic. Calculate Q, W, ∆U, and ∆H for each step of the process and for the cycle. Take CP = (7/2)R and CV = (5/2)R.
In a natural gas liquefaction plant, the liquefied natural gas (LNG) enters a cryogenic turbine at 30 bar and –160°C at a rate of 20 kg/s and leaves at 3 bar. If 115 kW power is produced by the turbine, determine the efficiency of the turbine. Take the density of LNG to be 423.8 kg/m3.
Refrigerant 134a enters a well-insulated nozzle at 200 lbf/in.2, 200°F, with a velocity of 120 ft/s and exits at 50 lbf/in.2 with a velocity of 1500 ft/s.For steady-state operation, and neglecting potential energy effects, determine the temperature, in °F, and the quality of the refrigerant at the exit. P.S. Kindly show your solution for obtaining the quality x2.
A turbine operating under steady-flow conditions receives steam at the following state: pressure, 13.8 bar; specific volume 0143 m3/kg, and velocity 30 m/s. The state of the steam leaving the turbine is as follows: pressure 0.35 bar, specific volume 4.37 m3/kg, and velocity 90 m/s. The difference in elevation is negligible. Heat is rejected to the surroundings at the rate of 0.25 kW, the turbine develops 103 kW of power and the rate of steam flow through the turbine is 0.5 kg/s. Calculate the change in internal energy of the steam
during reversible process, 2.09 kg/s of gas rejects 322.9 kJ/s of heat isothermally at 25.5 degrees C. (for this gas, cp= 2.14 kJ/kg-K and cv= 1.62 kJ/kg-K). The initial pressure is 551.7 kPa. determine the work steady flow of the process if change in PE= 2.8 kJ/s and change in KE= 6.2 kJ/s