Three loads are connected in parallel to a 220/0°Vrms ac source. Load 1 absorbs 80kVars at 0.85 pf lagging, load 2 absorbs 90kW and 50kVAR leading and load 3 absorbs 100kW at pf =1. a) Find the equivalent impedance. b) Find the overall power factor. c) Calculate the total real, reactive and apparent power.

Three loads are connected in parallel to a 220/0°Vrms ac source. Load 1 absorbs 80kVars at 0.85 pf lagging, load 2 absorbs 90kW and 50kVAR leading and load 3 absorbs 100kW at pf =1. a) Find the equivalent impedance. b) Find the overall power factor. c) Calculate the total real, reactive and apparent power.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
a. Find the total impedance ZT in polar form b. Draw the impedance diagram c. Find the current I and voltages VR , VL , and Vc in phasor form d. Draw the phasor diagram of the voltages E, VR, VL and VC, and the current I. e. Verify Kirchhoff’s voltage law around the closed loop. f. Find the average power delivered to the circuit g. Find the power factor of the circuit, and indicate whether it is leading or lagging.
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
a. Find the total admittance and impedance in polar form b. Draw the admittance and impedance diagram c. Find the voltage E and currents IR , IL , and Ic in phasor form d. Draw the phasor diagram of the currents Is, IR, IL and IC, and the voltage E. e. Verify Kirchhoff’s current law at one node f. Find the average power delivered to the circuit g. Find the power factor of the circuit, and indicate whether it is leading or lagging. h. What happened if R= 10 Ω
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
Consider the current i(t)= 30sin(100t+90o) mA. is applied the circuit given below. a) Find and draw phasor equivalent of the circuit b) Find Iload and Vload phasors and and draw them on the real-imaginary axis. Find iload(t) and vload(t) via inverse phasor, comment phase angles c)Find active, reactive and complex power (P,Q,S) absorbed by the load. please fast
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
A Y-connected balanced three-phase source is feeding a balanced three-phase load. The voltage and current of the source coil are: Calculate the following: The rms phase voltage. The rms line-to-line voltage. The rms current in the source. The rms current in the transmission line. The frequency of the supply. The power factor at the source side, state leading or lagging. The three-phase real power delivered to the load. The three-phase reactive power delivered to the load. If the load is connected in delta configuration, calculate the load impedance.
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?