Three-Phase AC Circuits Example 8.14 Three identical coils connected in delta across 400 V, 50-Hz, 3-phase ac supply, take a line current of 17.32 A at power factor of 0.8 lagging. Calculate (i) the phase current (ii) the resistance and inductance of each coil (iii) the power drawn by each coil. [U.P. Technical Univ. Electrical Engineering February 2002]

Three-Phase AC Circuits Example 8.14 Three identical coils connected in delta across 400 V, 50-Hz, 3-phase ac supply, take a line current of 17.32 A at power factor of 0.8 lagging. Calculate (i) the phase current (ii) the resistance and inductance of each coil (iii) the power drawn by each coil. [U.P. Technical Univ. Electrical Engineering February 2002]

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21P: An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor...

See similar textbooks

Similar questions

Is it possible to measure the phase-shift angle in an AC single-phase circuit by an indirect method using an ammeter and a voltmeter? - Yes, but an instrument must be added to measure the active resistance of the load. - Yes, but an instrument must be added to measure the active power dissipated by the load. - Yes, but an instrument must be added to measure the frequency.
Residential AC voltage for many European countries is 230 VRMS at 50 Hz. Calculate the following quantities for the AC signal: peak voltage, VP (in V); peak-to-peak voltage, VPP (in V); and period, T (in ms).
When an impedance coil is connected to a 114 volt 60 cps source, the current is 3 A. If the current rises to 4 A when a 116 volt 25 cps is is impressed across the coil, determine the values of the resistance and inductance of the coil.
34.1. Enumerate five step-by-step procedure of Nodal analysis method in application to ac electric circuit problem solution or analysis.
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
Exercise 2: Resistances connected in Series-Parallel across a Sinusoidal AC Supply Calculate the following: a) Calculate the peak to peak voltage (Vpk-pk) and peak to peak current (I pk-pk) b) Current flowing through the circuit. (Irms) c) Voltage across resistors R9, R12, R14. (Vrms) d) Current flowing through the resistors R9, R10,R14. (Irms) e) Calculate the time period of the waveform Consider V=3.535Vpk and F=1.5 kHz
The cosine angle between the voltage and current in an AC circuit is known as power factor. With aid of suitable diagram, describe the power factor that is referred as unity, leading and lagging.
A 100KVA, 220V, a star-connected alternator is loaded at full load and at 60% pf lagging.The effective AC resistance per phase is 0.01411Ω. If the synchronous reactance is 4.5times the effect of the armature leakage reactance wherein the later is 0.046 Ω perphase, find(a) the phase voltage that would be generated at the load if the circuit were operating normally(b) What no-load open-circuit phase voltage must be present in order to circulate full-load current in short-circuit state while maintaining the same speed and field current?(c) What is the terminal phase voltage of the alternator when it is under a shorted load condition? Give an explanation in support of your response using just one sentence. The IA phasor should be used as the reference one.
q1: Discussion of power quality aspects that need to be considered before installing the power factor correction unit
A 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 10 and 10 A respectively and are fed from the cable at distance of 15 and 15 respectively. Calculate the voltage available across load 1 and 2
A single phase circuit with a given load 3 ohm resistance and inductive reactance of 4 ohms as well. The voltage is being supplied 220 Volts with a reference angle of 30 degrees at 60 Hertz frequency. Solve for P,Q, S. and power factor.
q13/ choose the correct answer The variation of the load is considered over a period of one year in an annual load curve. Select one: True False