Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.2 in., d = 15.6 in., a = 3.5 in., and t= 0.4 in. For a vertical shear force of V = 48 kips, determine the shear flow through the welded surface at B. d B a b Answer: qB = i 4.78 kip/in.

Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.2 in., d = 15.6 in., a = 3.5 in., and t= 0.4 in. For a vertical shear force of V = 48 kips, determine the shear flow through the welded surface at B. d B a b Answer: qB = i 4.78 kip/in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The thin plate of mass 8 kg is held in place as shown. Neglecting the mass of the links, determine…

A: Given that: Mass of the plate ABCD = 8 kg It is required to determine: Immediately after the wire…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 380 Ib. Dimensions of…

Q: transmit 50 kW power to a machine. The sheave is 10 inches in diameter and turns at 1200 rpm, while…

Q: Q#2: the condenser of Geothermal Heat Pump will be cooled by A pipe with dimeter 3 cm buried in a…

Q: 1. A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 40 kgm/s. The…

Q: A solið, homogeneous sphere with a mass of mo, a radius of ro and a density of po is placed in a…

A: Buoyancy can be understood as the tendency of a particular object to float in a fluid. Liquids &…

Q: 2 litre of petrol weighs 14N. Calculate the specific weight, density, specific volume and specific…

Q: Q#2: the condenser of Geothermal Heat Pump will be cooled by Ap dimeter 3 cm buried in a soil the…

Q: 1. (Problem 7.3 from the text book) For the given state of stress, determine the normal and shearing…

Q: 4 ft A 5 ft→ 7 ft→B At a forward speed of 30 ft/s, the truck brakes were applied, causing the wheels…

Q: Calculate the maximum volume flow rate of fuel oil at 45°C at which the flow will remain laminar in…

Q: Convection heat transfer through the plate is 180 w/m?k. Find convection heat transfer coefficient…

Q: Consider air as an ideal gas at 325 K and 0.865 m³/kg. Using total differential relations, determine…

Q: Will cause a shear stress of 6000 psi? 3.41 The constant wall thickness of a steel tube with the…

A: Given Radius, R = 10 mm Diameter, D = 20 mm Torque, T = 600 N. m Length, L = 30 mm Find…

Q: Figure Q3 A car A is travelling along a straight path, while a lorry B is travelling along a…

Q: What is the main difference between rigid bodies and deformable bodies o 5:50

A: A rigid body does not deform or change shape Example : metallic rod

Q: B

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

Q: The truck is moving along a 15 m span of beam. The front axle is 16 kN, the middle is 36 kN and the…

Q: team enters the turbine of a simple vapor power plant with a pressure of 10 MPa and temperature T,…

A: Given-P1=10MPa=100barT1=580°Cfrom steam table-S1=S2'=6.847 KJ/kg kh1=3576.2 KJ/kg…

Q: Part A Let the pressure gradient in the pipe be 1400 Pa/m and the diameter of the pipe be 4.0 mm.…

Q: Questions 1. Steam from the turbine exhausts directly into the (shell/water) of the condenser. 2. As…

A: Steam in the turbine does work and when steam exhausts from condenser it is converted to low temp…

Q: Consider the Exponential Weighted Moving Average that is used to estimate the Round Trip Time (RTT)…

A: In the exponential weighted moving average method, the maximum weighted is given to the targetted or…

Q: Car A is moving along a straight road is de- celerating at a rate of 10 m/s as shown. Car B is…

Q: A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and…

Q: P A B D F H y C E G 4 panels at 10 ft = 40 ft

Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…

Q: Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of…

Q: 2 Measurements in a particular area yielded the following t-octave band pressure Center frequency…

A: Measurement in a particular area yeilded the following t-octave band pressure levels: Center…

Q: Briefly explain why placing a PVC pipe nipple between a black iron water pipe and a copper pipe…

A: Corrosion is a process of destruction of the metal. There are galvanic corrosion, metallic…

Q: Part A The pendulum in (Figure 1) consists of a 2-kg disk and slender rods AB and DC which have a…

Q: 4. A proposal for a “Smart" car seat operates by detecting the weight of the passenger and comparing…

A: Given The answer is given below.

Q: The hydrometer shown in Fig. P2.87 with no mer- cury has a mass of 0.01 kg. It is designed to float…

Q: Q#2: the condenser of Geothermal Heat Pump will be cooled by A pipe with dimeter 3 cm buried in a…

Q: From the viscosity expriment: - Calculate the value of the viscosity coefficient and its propagated…

A: The ratio of shearing stress to the fluid's velocity gradient is known as the coefficient of…

Q: The cross-sectional area of the bar is 5 cm². Use E = 70 GPa for aluminum, and E = 200 GPa for…

Q: Problem. A reversible heat engine operates between high and low temperature reservoirs at TH and TL,…

A: given; In rigid tank;gas moles(n)=4kmolehigh temperature(T1)=500Kpressure(P)=4MPa…

Q: Water flows along a horizontal pipe of diameter 75 mm. An orifice plates of diameter 50 mm is…

Q: vel with constant speeds of UA = 31.39 m/s and UB = 18.82 m/s when they leave the pier at O at the…

Q: F = 100 N p.125 m, 0.3 m 025 m - 300 N Determine the magnitude and sense of the resultant moment…

A: As per given question F1=100N F2=300N We have to determine moment produce by force system

Q: A simply supported wood beam that is 6.6 m long carries a 49 kN concentrated load at B. The…

Q: The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 15.77 ksi for…

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

Q: 5. Locate the centroid y of the channel's cross-sectional area, then determine the moment of inertia…

Q: The heat flux (q) can be computed with Fourier's law Where q has units of W/m2 and k is the thermal…

A: Given : To find : Heat flux

Q: 3. A water from Agno River is pumped at 13.3 L/s using a submerged pump at an efficiency of 78% that…

A: Consider Bernoulli’s equation for steady flow between the points (1) and (2).…

Q: Please handwriting make the solution very simple not long 3. [Ch7 – 2] For the first-, second-, and…

A: given details

Q: 2 litre of petrol weighs 14N. Calculate the specific weight, density, specific volume and specific…

Q: An oil having a density of 833 kg/m3, and a viscosity of 3.3x10^-3 Pa-s is pumped from an open tank…

Q: Both 6-in.-radius wheels roll without slipping on the horizontal sur- face. Knowing that the…

Question

X Incorrect
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 5.2 in., d = 15.6 in., a = 3.5 in., and
t = 0.4 in. For a vertical shear force of V = 48 kips, determine the shear flow through the welded surface at B.
В
a
Answer:
9B =
i
4.78
kip/in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: INTRODUCTION

VIEW

Step 2: TO DETERMINE THE SHEAR FLOW THROUGH WELD SURFACE AT B.

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The shear stress at the inner surface of hollow circular section is __
Determine maximum shear stress
If a beam has a rectangular cross section of heigh 300mm and width 60mm. In one cross section plane the beam experiences a shear force of 2x10^6 N. How do I work out the; 1 - shear stress at neutral axis 2 - the bottom surface 3 - 20mm from the top surface
Sketch shear flow diagram and locate position of shear center for V = 10R (N) acting downwards. Assume uniform thickness of R/360 (mm) for all segments of section shown below. Perform neat and detailed calculations using appropriate value of R given below Note R=993
per the attached figure: if the applied shear force V = 14 kip, determine the maximum shear stress in the member.
The channel beam with b= 300 mm, h=150 mm, and constant thickness of t=15 mm is subjected to a shear of V=15 kN. Calculate the maximum shear stress of the beam.
A T- section is the cross section of a loaded beam as shown.Given: U1= 20 kN/m; M1 = 100 kN-m; P1 = 120 kN a.) Draw the shear diagram using graphical solutionb.) Determine maximum shearing stress.b.) Determine the shearing stress at the junction of the T-section.
Consider a tube having a rectangular cross-section as shown below. The tube is subject to two twisting moments of 70 N - m . Determine the average shear stress developed at point A. The tube is fixed at the other end. a) 1.75 MPa b) -1.65 MPa c) 4.086 MPa d) 2.095 MPa
Beam cross section is shown below. If a resultant shear force, V acting at the beam cross section is 40 kN, (a) Determine the shear stress due to bending at points C (b) Sketch the shear stress distribution over the beam cross section and describe the shear stress pattern at the interface between flange and web. Given I NA = 301.3 x 10-6 m4
What is the maximum normal stress, MPa, due to bending on section C? For S200x27.4, S = 235µm^3. Answer in whole numbers, no units. (Example: 123MPa --> 123)
Determine the maximum shear stress (in ksi). AT = 654 lb ft Diameter =3.7 in J =1.5in4 G = 11,000 ksi
2. The W360 x 262 section carries a vertical shear force of 650 kN. For this section, calculate:(a) the minimum shear stress in the web;(b) the maximum shear stress in the web and(c) the percentage of the vertical shear force carried by the web.