Three wye-connected load impedances, z = 15260° Q, 202 - 30° 2, and z = 10445 N, are connected to an abc- z, sequence, balanced 3-phase, wye-connected source with a line voltage of 208 V. A conductor of impedance 1 + j5 Q is used to connect together the neutral points of the source and the load. The line impedance per phase is 4 + j200. Calculate the load phase currents and voltages, and the neutral current.

Three wye-connected load impedances, z = 15260° Q, 202 - 30° 2, and z = 10445 N, are connected to an abc- z, sequence, balanced 3-phase, wye-connected source with a line voltage of 208 V. A conductor of impedance 1 + j5 Q is used to connect together the neutral points of the source and the load. The line impedance per phase is 4 + j200. Calculate the load phase currents and voltages, and the neutral current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.51P: A three-phase line with an impedance of (0.2+j1.0)/ phase feeds three balanced three-phase loads...

See similar textbooks

Similar questions

Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4j2.7) per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging, and the other 132 kW at unity power factor. The line-to-line voltage at the load end of the line is 2203V. Compute (a) the line-to-line voltage at the source end of the line. (b) the total real and reactive power losses in the three-phase line, and (c) the total three-phase real and reactive power supplied at the sending end of the line. Check that the total three-phase complex power delivered by the source equals the total three-phase comp lex power absorbed by the line and loads.
Figure 2.33 gives the general -Y transformation. (a) Show that the general transformation reduces to that given in Figure 2.16 for a balanced three-phase load. (b) Determine the impedances of the equivalent Y for the following impedances: ZAB=j10,ZBC=j20, and ZCA=j25. ZAB=ZAZB+ZBAC+ZCZAZCZA=ZABZCAZAB+ZBC+ZCAZBC=ZAZB+ZBAC+ZCZAZAZB=ZABZBCZAB+ZBC+ZCAZCA=ZAZB+ZBAC+ZCZAZBZA=ZCAZBCZAB+ZBC+ZCA
A balanced delta-connected lood with impedance per phase of 30<30 ohms is connected to an abc-sequence balanced three-phase source with eAC = -120√2 cos (120πt + π/6) V through conductors with negligible impedances. Determine the line currents, load phase currents and the total complex power drawn by the lood. Write your values in polar form.
A balanced delta connected load of 13+j16 ohm per phase is connected at the end of a three-phase line. The line impedance is 2+j11 ohm- per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 Vrms. Taking phase "a" voltage Va as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal.
A balanced three-phase source with grounded neutral has line-to-neutral voltages of 132.7906 volts with an-bn-cn sequence. This source has an internal series impedance of 0.2+j2.5 ohms per phase. It supplies power to an unbalanced three-phase wye, neutral grounded, load with impedances: Zan = 18-j10; Zbn = 15+j25; Zcn = 20+j30 ohms. If line a is open creating a series fault at line load-side, what is the magnitude of the line current in line b in amperes?
A set of balanced three-phase transmission lines with line-to-line voltages of 13 kV is connected to a balanced wye load with phase impedance of 8 + j3 Ohms. What is the real power delivered to the three-phase load?
A balanced, positive-sequence, Y-connected voltage source with Eab = 480∠0o volts is applied to abalanced-∆ load with Z∆ = 30 ∠40o Ω. The line impedance between the source and load is ZL = 1 ∠850 Ω.for each phase. Calculate the line currents, the ∆ -load currents, and the voltages at the load terminals.Recall that ZY = Z∆/3
A balanced three-phase source with grounded neutral has line-to-neutral voltages of 132.7906 volts with an-bn-cn sequence. This source has an internal series impedance of 0.2+j2.5 ohms per phase. It supplies power to an unbalanced three-phase wye, neutral grounded, load with impedances: Zan = 18-j10; Zbn = 15+j25; Zcn = 20+j30 ohms. If there is a line-to-line fault at lines b and c load-side, what is the magnitude of the fault current in amperes?
The phase voltage at the terminals of a balanced three-phase Yconnected load is 2400 V. The load has an impedance of 16 + j12 Ω/ϕ and is fed from a line having an impedance of 0.10 + j0.80 Ω/ϕ. The Yconnected source at the sending end of the line has a phase sequence of acb and an internal impedance of 0.02 + j0.16 Ω/ϕ. Use the a-phase voltage at the load as the reference and calculate (a) the line currents IaA, IbB, and IcC; (b) the line voltages at the source, Vab, Vbc, and Vca; and (c) the internal phase-to-neutral voltages at the source, Va ′n, Vb′n, and Vc′n.
an abc sequence, balanced 3-ph supply with a line voltage of 400V supplies two balanced 3 phase loads that are connected in parallel. The first load is Y-Connected and has an impedance of 30+j40 ohms per phase. The second load is triangle-connected and has an impedance of 60-j45 ohms. The line has an impedance of 2 +j4 ohms. Taking the phase voltage Ea as reference. determjne the line currents, the phase currents per load, and the total complex power supplied by the source
A balanced three-phase source with grounded neutral has line-to-neutral voltages of 120 volts with an-bn-cn sequence. This source has an internal series impedance of 0.1+j1.5 ohms per phase. It supplies power to an unbalanced three-phase wye, neutral grounded, load with impedances: Zan = 40+j30; Zbn = 36-j15; Zcn = 18+j24 ohms. If there is a single-line-to-ground fault at line a load-side, what is the magnitude of the fault current in amperes?
The one-line diagram of a three-phase power system is as shown in the figure attached. Impedances are marked in per unit on a 100-MVA, 400-kv base. The load at bus 2 is S(sub 2) = 15.93 MW - j33.4 Mvar, and bus 3 is S(sub 3) = 77MW + j14 Mvar. I tis required to hold the voltage at bus 3 at 400 angle 0 degrees kV. Working in per unit, determine the voltage at buses 2 and 1.