-:) To replace the regular light bulb with a high-efficiency light bulb, what is the upper price limit to make the high-efficiency light bulb economically attractive? (Ignore the interest rate.) (Electricity: $0.15/kWh) (a) 3.25 (d) 5.00 Type of light bulb Regular High-efficiency (b) 4.21 (e) 23.8 Cost Power ($/piece) (W) 1.00 100 ? 15 Life time (hours) 2000 1800 (c) 46.2

-:) To replace the regular light bulb with a high-efficiency light bulb, what is the upper price limit to make the high-efficiency light bulb economically attractive? (Ignore the interest rate.) (Electricity: $0.15/kWh) (a) 3.25 (d) 5.00 Type of light bulb Regular High-efficiency (b) 4.21 (e) 23.8 Cost Power ($/piece) (W) 1.00 100 ? 15 Life time (hours) 2000 1800 (c) 46.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A ship lying in the mouth of a river in water of density 1030kg per cu.m and the displacement is 12 000 tons. The ship is to proceed up river and berth to dock at water with density 1008 kg per cu.m with the same draft. what is its new displacement, in tons? 256.31 tons 11650 11 744 256 000
The total consumption of electrical energy in the United States is about 1.0 1019joules per year.What is the average rate of electrical energy consumption in watts?If the population of the United States is 300 million, what is the average rate of electrical energy consumption per person?The sun transfers energy to the earth by radiation at a rate of approximately 1.0 kW per square meter of surface. If this energy could be collected and converted to electrical energy with 40 % efficiency, how great an area (in square kilometers) would be required to collect the electrical energy used by the United States?
2- Please I want a solution of this question. Many Thanks Determine the average wind velocity required to produce 4 MW of effective power by a wind turbine having the following data: blade length 65 m, hub diameter 6 m, air density 1.12 kg/m3, power coefficient 0.6, gear efficiency 85%, electrical efficiency 90% and generator efficiency 95%.
Engineering economics Investing in Electrical Efficiency Two pumps capable of delivering 100 hp to an agricultural application are being evaluated in a present economy study. The selected pump will only be utilized for one year, and it will have no market value at the end of the year. Pertinent data are summarized as follows: ABC Pump XYZ PumpPurchase price $2,900 $6,200Maintenance cost $170 $510Efficiency 80% 90% If electric power costs $0.10 per kWh and the pump will be operated 4,000 hours per year, which pump should be chosen? Recall that 1 hp = 0.746 kW. Choose XYZ because it provides least cost.
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
I need help with the second table. and these questions 1- If 1 gallon of oil = 1.4 therm, how many gallons have been wasted by heat loss in Feb? (1 therm = 100,000 BTU) 2- If $1.30 per therm, how much did you waste from house heat loss in Feb?
In the United States, energy for household heating is generally sold using English units, e.g., therm, gal, and cord. A house in Wisconsin uses 1200 therms of thermal energy during the heating season. Calculate the cost of fuel if the furnace uses (a) natural gas with an efficiency of 70%; (b) No. 2 fuel oil, efficiency 65%; (c) kerosene, efficiency 99.9% (unvented); and (d) wood with l5% moisture with an efficiency of 50%. Use the data in Tables 2.2, 2.7, and 2.13. The efficiencies are based on the HHV. Assume the cost of natural gas is $8/MBtu, the cost of No. 2 fuel oil is $3/gal, the cost of kerosene is $3.50/gal, and the cost of wood is $100/cord. Assume the bulk density of cord wood is 30 lbm/ft3 .
Unreasonable Results - A slightly deranged Arctic inventor surrounded by ice thinks it would be much less mechanically complex to cool a car engine by melting ice on it than by having a water-cooled system with a radiator, water pump, antifreeze, and so on. (a) If 80% of the energy in 1.00 gal of gasoline is converted into “waste heat” in a car engine, how many kilograms of 0C ice could it melt? (b) Is this a reasonable amount of ice to carry around to cool the engine for 1.00 gal of gasoline consumption? (c) What premises or assumptions are unreasonable?
1. Energy consumption in a country from 2001 to 2011 increased from 1041.3 million to 1526.1 million BOE (barrels of oil equivalent). If the high calorific value (HHV) of the oil is 141,000 kJ/gallon what is the increase in energy consumption over 10 years in Joule units. What is the rate of energy consumption per year? 2. Based on data on the rate of energy consumption per year from question no. 1, if the growth rate energy 2.5% per year, calculate the doubling time (td) and what is the approximate rate of energy growth in 2021.
In the design of a jet engine part, the designer has a choice ofspecifying either an aluminium alloy casting or a steel casting. Either materialwill provide equal service, but the aluminium casting will weigh 1.2 kg ascompared with 1.35 kg for the steel casting.The aluminium can be cast for $ 80.00 per kg. and the steel one for$ 35.00 per kg. The cost of machining per unit is $ 150.00 for aluminiumand $ 170.00 for steel. Every kilogram of excess weight is associated witha penalty of $ 1,300 due to increased fuel consumption. Which materialshould be specified and what is the economic advantage of the selection perunit?
Need complete answer ASAP... An object is submerged below the surface of the sea with an exerted pressure of 99.92 bar. How deep is the object submerged? The density of sea water is 1020kg/m3, the gravitational force is 9.7 m/s2, and the atmospheric pressure is 0.98 bar.