Transmitter: a carrier frequency of 108 kHz and a modulating frequency of 3.4 kHz is plied to an amplitude modulator. The USB and the LSB are both transmitted to the distant eceiver, with a suppressed carrier. Receiver: the resultant USB and LSB from the transmitter are input to an amplitude demodulator. A carrier frequency of 108 kHz is reintroduced to the demodulator. Determine the following: 1. The LSB and USB at the output of the modulator. 2. The LSB and USB at the output of the demodulator.

Transmitter: a carrier frequency of 108 kHz and a modulating frequency of 3.4 kHz is plied to an amplitude modulator. The USB and the LSB are both transmitted to the distant eceiver, with a suppressed carrier. Receiver: the resultant USB and LSB from the transmitter are input to an amplitude demodulator. A carrier frequency of 108 kHz is reintroduced to the demodulator. Determine the following: 1. The LSB and USB at the output of the modulator. 2. The LSB and USB at the output of the demodulator.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

You need a 20kHz sinusoid signal. What type of signal generator are you going to use? Discuss the setting of this signal generator to produce the required signal. You need an AM signal with 800kHz carrier frequency and 1kHz modulating signal. What laboratory equipment will you use? Describe the setting of the equipment to produce the required signal. The RF signal generator is used to produce an AM signal using an AF signal generator as the source of modulating signal. The RF generator is then connected to the oscilloscope. The oscilloscope displays an overmodulated AM signal. What adjustment would you do to produce an undistorted AM signal?
Problem1: the figure shows multiple modulation schemes for the signal that is given by the dashed line sinusoidal function, the X-axis is the time axis is seconds and the Y-axis is the amplitude. Answer the following: 1. What is the modulation scheme in A? 2. What is the modulation scheme in B? 3. What is the sampling frequency? 4. What is the value of the duty cycle in A?
A 1500 KHz carrier with amplitude of 50 V is amplitude modulated by 2 –KHz sine wave tone with a peak voltage of 15 V. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
An AM signal is provided below. The carrier frequency is 500 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y-axis is the amplitude of the AM signal. Answer the following questions with appropriate solutions if applicable. Determine the type of AM signal in the figure. Determine the frequency of the message signal in Hz. Determine the peak voltage level of the carrier in V. Determine the peak voltage level of the modulating signal in V. Determine the modulating index. Determine the power of the unmodulated carrier in W. Assume the load resistance to be 1-ohm. Determine the power of sidebands in W.
An audio signal given by 15 sin(4000ntt) + 20 sin(8000mt) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60 sin(100,000nt) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why?
Transmitter: a carrier frequency of 108 kHz and a modulating frequency of 3.4 kHz is plied to an amplitude modulator. The USB and the LSB are both transmitted to the distant eceiver, with a suppressed carrier. Receiver: the resultant USB and LSB from the transmitter are input to an amplitude demodulator. A carrier frequency of 108 kHz is reintroduced to the demodulator. Determine the following: 1. The LSB and USB at the output of the modulator. 2. The LSB and USB at the output of the demodulator.
What is Frequency Modulation? Draw the waveforms.
A carrier wave of 100 MHz is frequency modulated by a 100 KHz sinewave with amplitude of 20 V, if the modulator sensitivity is 25 KHz/V, find If the FM modulator are replaced by PM modulator, compute the frequency deviation The frequency deviation of the modulated signa
help please with explain A narrowband FM signal has a carrier frequency of 110 kHz and a deviation ratio of 0.05. The modulation bandwidth (signal bandwidth) is 10 kHz. This signal is used to generate a wideband FM signal with a deviation ratio of 18 and a carrier frequency of 98 MHz. a) Give the required value of frequency multiplication, n. b) Give two frequencies for the mixer to give the desired carrier. c) Define the required bandpass filter (center frequency and bandwidth).
Design an Armstrong indirect FM modulator to generate an FM carrier with carrier frequency of 1 and ∆= 75. A narrowband FM generator is available at a carrier frequency of 100 and a frequency deviation ∆= 10. The stock room also has an oscillator with an adjustable frequency in the range of 10 to 11 MHz. There are also frequemncy doublers, triplers and quantiplers.
Consider the following continous time signal x(t). Assume that the signal was sampled at a sampling frequency of 20 Hz. Plot the magnitude spectrum of the sampled signal as a function of cyclic frequency. Be sure to include n values of up to +-2. Label x and y axis. Did aliasing occur? If so, what is the aliased frequency? x(t) = 1 + 2cos(2pi25t)
then second questrion po eh eto 2. Determine the over-all transmittance of the signal flow graph shown below.