True or False: The BREAK command requires two separate points when breaking a circle.

Q: True or False: The JOIN command requires that line segments must lie end to end with no gaps or…

A: The JOIN command joins similar objects to form a single unbroken object. The JOIN command combines a…

Q: True or False: The LENGTHEN command doesn’t work with arcs.

A: While using the LENGTHEN command, the Delta and angle options allows the user to lengthen or shorten…

Q: Which of the following is constructed problem? Machinery break down O Stuck in a traffic jam at a…

A: The constructed problem is a problem which is set by someone . It creates disturbance in labour and…

Q: is used to cut machine other material. O Chromium steel Nickel steel O Martensitic tool steel O Tool…

A: To find the material that are used to cut machine other material .

Q: g two (2) cylincer types:

A: 1. SINGLE ACTING CYLINDER 2.DOUBLE ACTING CYLINDER

Q: When cutting a beam at a point within a distributed load, you should always

A: The uniform distributed load is the force applied on an area while the point load is the force…

Q: Mechanical advantage is the ratio of effort to load. a) True b) False

A: Mechanical advantage is the ratio of effort to load. a) True b) False

Q: Once answered correctly will UPVOTE!!

A: Given that ,  ω=4.5 rad/s α=7.5 rad/s2

Q: Writing references is necessary

A: The vibration parameters are – Amplitude of vibration Acceleration, velocity, and displacement.…

Q: How much change in the energy of wind will take place if blade length becomes 3 times? No Change 27…

A: Given data: Length of the blade (Lf) = 3L Need to determine the change in the energy of wind.

Q: Sketch the proper end shape of a soapstone that is to beused for marking metal.

A: The design of the work metal is marked with soapstone & chalk line to ensure appropriate…

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: the force needed to deflect 1 inch of length is called

A: The force needed to deflect one inch of length can be called as stiffness.

Q: The shortest distance between a line and a point is achieved when? a) A line is drawn at 90 degrees…

A: Given  The shortest distance between a line and a point is achieved when? a) A line is drawn at 90…

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: Question 8  I put C and it was incorrect

A: To determine: Correct technician among A and B who are discussing the suspension and ignition switch…

Q: The depth measurement is done by ___________________part of a Vernier Caliper. Ratchet Anvil Spindle…

A:

Q: True or False: The OFFSET command cannot be used on closed objects

A: The OFFSET command is used to create parallel lines, parallel curves and concentric circles at a…

Q: can make it in Solidwork

A: Given Structure To find 3D model

Q: Dad with an angle of 10° and radius

A:

Q: When two links of a mechanism become collinear (forming a straight line), the links are said to be…

A: A link is defined as a member of a mechanism that connects with other members of mechansim and…

Q: If a force doubled, impulse will triple. True or false

A:

Q: at A on the wall.

A: Answer= 14m/s

Q: Pictures A and B show two different ways of holding a workpiece in the vice while using hacksaw. The…

A: We have to given answer of above question Pictures A and B show two different ways of holding a…

Q: troid, ỹ on axis x'- x ' for the parts cross-sectic

A:

Q: the correct order of

A: Given; Correct order of efficiencies for otto, dual and diesel cycle is ?  where,  For the same…

Q: An 'angle plate' is used to A. Hold a workpiece B. Mark various angles on the workpiece and hence…

A: An angle plate is a work holding device used as a fixture in metalworking.

Q: The tool used for marking center is __________. a.   Steel rule   b.   Divider   c.…

A: Solution:

Q: ke angle is 0°. The minimum value of sh

A:

Q: what maximum angle can the ramp make with the horizontal before the block starts to slip down?

A:

Q: Lathe Machine tool is an example of two axes machines Select one: True False

A: The lathe machine tool is given

Q: While Drilling it is permissible to leave the check key in check while drilling a hole.

A: While Drilling it is permissible to leave the check key in check while drilling a hole. Answer:…

Q: The time taken to drill a hole

A: Given; Feed rate of a drill is;   f= 0.25 mm/revAt a rotating speed at, N= 300 rpmWhere, Plate…

Q: Safety goggles are required when working on lathe machine. Select one: True False

A: Lathe machine is one of the oldest machine used in manufacturing field. Due to its It's versatile…

Q: resistance to motion caused by the shoveling

A: Given: Q= 12 ft3/s V=14 ft/s specific weight =5.5 lb/ft3 TO determine: resistance to motion

Q: volume of metal

A: Given; While cooling a cubical catsing of side, 40 mmVolume shrinkage=3%, 4% and 5%  liquid state…

Q: e digging a small E

A: Given- m= 17kg force on prybar = 242N   To calculate a)Including weight  Fc b) Excluding weight Fc

Q: Chain block pulley is connected to a crane and is used to lift Heavy objects manually Select one:…

A: A chain block is a mechanism used for lifting and lowering heavy loads via a chain and they are also…

Q: once answered correctly will UPVOTE!!

A:

Q: The cause of an induced angle

A: Solution ;

Q: When measured the moment of force, it need tunneling point *

A: This question is based on the concept of moment of force

Q: Tools should not be kept on machine while using the machine tool. Select one: True False

A: Answer: TRUE

Q: A rod consists of two parts that are made

A: Kindly refer attached files.

Q: Define the term Angle of Repose

A: The slope of cut and fill at the excavation site which is measured in feet of horizontal to feet of…

Q: True or False: A fillet radius can be drawn between two parallel objects.

A: When filleting two parallel lines, a 180 degree arc will join the two lines. The radius of the…

Q: Magnetic clamps can be used for marking aluminum sheets. Select one: True False

A: Magnetic clamps: The magnetic clamps are used to hold pieces of metals  in their required position…

Q: at is true answer

A: 1. Number of links=42. Number of full joints=43. Number of half joints=04. DOF(mobility)=3N-1-2J…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.