Magnetic clamps can be used for marking aluminum sheets. Select one: True False

Q: With the use of an Alloy joining two or more metal pieces called as_ Select one: a. Printing b.…

A: Solder is a metal alloy that will tend to melt at a lower temperature than the metal which is being…

Q: What is a piece of 1/2" x 1" x 10' long stock commonly called?

A: Given:-  What is a piece of 1/2" x 1" x 10' long stock commonly called?

Q: 1(a) Draw and label any screw thread and a fastener separately.

A: As per given question  Draw and label any screw thread and a fastener separately

Q: Task 2: Is Obrass >OR < aFe bimetallic strip since the bimetallic strip curves in towards iron side…

A: Write the expression of coefficient of expansion during heating. α=Lf-LiLi1Tf-Ti

Q: The poison's ratio is the ratio between stress to strain Select one: True False

A: Poisson's ratio is the ratio of lateral strain to the longitudinal strain. The strain in the…

Q: 14 Flashbacks are common in gas welding process if metal surface are not cleaned. Select one: True…

A: The above statement are false.

Q: The increase in size of the hole in a metal plate that is contact with a bolt is an indication of…

A:

Q: 5) In soft soldering a low melting range alloy of tin and lead is used as filler metal. Select one:…

A: It is true

Q: ength than A

A: introduction: here we find is the statement is false or true

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: What minimum diameter is required for the wire?

A: Given data: -  The length of the steel wire is L = 1.95 m. The permissible elongation is δ = 0.270…

Q: QUESTION 25 The direction of sliding of kinematically permissible wedges is less restrictive than…

A: Rock mechanism and fundamentals concept  ***As per our company policy we are supposed to do only 3…

Q: Which one of the following welding processes is suitable to weld bimetallic strips for measuring…

A: Given Bimetallic To find Welding

Q: 17. Which part of the marking gauge is used to mark To measure the ductility of weld metal b. To…

A: The correct option is option  c.

Q: What do the Discontinuity functions express?

A: A discontinuity function expresses that at the point of discontinuity either the limit doesn’t exist…

Q: What happens when the boards are bonded together?

A: When the boards are bonded together with an adhesive material, the mechanical interlocking mechanism…

Q: Label all forces that act on the metal

A: A piece of metal is submerged in the liquid and one end of the metal piece is fixed with a string.…

Q: A soldering iron 'bit' is made of?    A.Brass    B.Tin    C.Steel    D.Copper

A: We can find the answer as below A soldering iron 'bit' is made of?

Q: Filler rod material is same base metal used in gas welding process. Select one: True False

A: Above statement is true.

Q: Hard drawn copper rivets are u

A: Answer: d= 0.36in

Q: Figure 2.1 shows a stud fitting components and a steel plate. Please describe the procedure to…

A:

Q: , the minimum metric specification required for the bolt is

A: Given, From the given shows,  Three bolt system having, Shear yield strength,σyt=200 MPaFOS=…

Q: If rods of these materials are the same size, select the lightest metal rod. Titanium Carbon…

A:

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: separately

A:

Q: If cracks are present in the metal, they are removed through cold working. Select one:

A: Cold working processes are used to shape the metal with minimum loss below the recrystallization…

Q: Bolts and nuts are used for joining process. Select one: True False

A: Metal joining is defined as joining of two metal parts either temporarily or permanently with or…

Q: With the use of an Alloy joining two or more metal pieces called as Select one: a. Printing b.…

A:

Q: Steps how to draw a needle of a cannula using SOLIDWORK

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: Advantages and disadvantages of using smaller bolts than bigger bolts

A:

Q: 62. Silver is used as filler metal in soldering process. Select one: True False

A: Soldering is a process in which base material components are joined together by filler material…

Q: 2. Hooke's law holds good upto A.Yield point B.Limit of proportionality C.Breaking point D.Elastic…

A: To explain the Hooke's law limits

Q: oining process. Select one:

A: True

Q: False

A: It is False. Higher the gauge number, indicates thinner the sheet metal.

Q: 17. Which part of the marking gauge is used to mark lines on wood?

A: The gauge consists of a beam, a headstock, and scribing or marking implement, typically a pin,…

Q: What is the thickness of steel?

A: To find thickness of steel.

Q: Lap Joint Questions The following questions all use this figure. Assume a bolt will be put in each…

A: Given: To find: Number of fasteners counted  for calculating area of net cross section.

Q: What is meant when a metal is said to have goodweldability?

A: Weldability describes the ease with which a metal can be welded properly. The weldability of any…

Q: 61. Flashbacks are common in gas welding process if metal surface are not cleaned. Select one: True…

A: Flashbacks happens due to uneven metal surface in welding that build up a tip on the torch.

Q: Wielding is the only method of joining to ferrous metals together to make a permanent connection.

A:

Q: Comparison: Indicate if , or = Better Stiffness: Gold Tungsten

A: Subject : material science

Q: Hard soldering uses alloy of silver and _______ metal. a. Zinc b. Tin c. Lead d. Copper

A:

Q: Bolt material is 304 stainless steel. frame material is Aluminum. kindly assume all the other values…

A: Given: Frame material is made of Aluminum. And bolt material is stainless steel. And there are two…

Q: List the steps that should be followed to preciselytighten a bolt to specifications.

A: Common fasteners that join two or more pieces of work together include nuts and bolts. You will need…

Q: Two lengths of steel are aut off frm a 187.573 length for a job. Piece1 is 35.729" long and piece 2…

A:

Q: What is the depth, minor diameter, width of crest and root for a bolt 1⁄2 X 20 UNF

A: UNF = Unified National Fine Screw Thread.   The Nominal Major Diameter and Threads-per-inch (Pitch)…

Q: Question 28 Sae Answer Ir the part shown is assembled by fxed fasteners and the maximum size of the…

A: The engineering tolerance is defined as " the permissible limits of variation in the physical…