2. Two 1-mm diameter wires support the rigid bar as shown. Initially, the 300 mm long rigid bar ishorizontal. Determine the value of dimensions a and b so that when the load is applied in thebar, the bar will remain horizontal. After the load is applied using the computed values of a andb, the temperature increases by 15 degrees. What will be the angle of the bar with respect tothe horizontal after the temperature change? Use E = 200 GPa.100 cm75 cmabRigid bar100 N

Since in the question it is given that, the plate is still in the horizontal position after the…

Answered: Two 1-mm diameter wires support the…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.76P: The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.

See similar textbooks

Similar questions

Q;Determine the stiffness and elasticity matrices of the system below:
Mechanics of Deformable Bodies. Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following: a. Calculate the tension of the cable. b. Determine the diameter of the wire if the allowable stress is 125 MPa. c. If the diameter of the cable is 10 mm, find the deflection of the steel cable. d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
The force P is applied to the bar, which is made from an elastic perfectly plastic material. Construct a graph to show how the force in each section AB and BC (vertical axis) varies as P (horizontal axis) is increased. The bar has cross-sectional areas of 1 in2 in region AB and 4 in2 in region BC. Take sY = 30 ksi.
A rectangular block of size 200mm x 100mm x 80mm (i.e. length x width x depth) is subjected to a tensile force of 300 KN in the longitudinal direction. A tensile force of 100 KN on the 200mm x 80mm faces and a compressive force of 80 KN on the 200mm x 100mm faces. Take E= 2 x 10³ N/mm² and Poisson's ratio as 0.3. Calculate the changes in the dimensions and change in volume of the block.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine the modulus of elasticity and the modulus of resilience.
The central bar CD of the assembly is heated from 30 ° C to 180 ° C by means of an electrical resistance. Also the two bars AB and EF are heated from 30 ° C to 50 ° C. At the lower temperature of 30 ° C, the space between C and the rigid bar is 0.7 mm. Determine the force in bars AB and EF caused by the increase in temperature. Bars AB and EF are made of steel and each has a cross-sectional area of 125 mm ^ 2; CD is aluminum with a cross-sectional area of 375 mm ^ 2. Steel = 200GP; Ealuminum = 70 GPa; alpha steel = 12 X10 ^ -6 (1 / ºC); alpha aluminum = 23 X10 ^ -6 (1 / ° C).
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
A smooth-walled 100 mm edge steel bucket is filled with rubber to form a rubber bucket embedded within the steel bucket. If the rubber hub is compressed by a 100 kN force, determine: a) The normal contact stress between the rubber and the inner walls of the steel. b) The change in volume experienced by the rubber bucket. Consider the following: - The steel bucket is rigid. - There is no friction between the smooth walls of the steel bucket and the rubber (shear stress equal to zero between steel and rubber). - Rubber properties: E = 4 MPa and v = 0.45.
1.Determine the total extension of the composite spring when subjected to the maximumload.2.Calculate the total strain energy in the spring assembly.
Force P is applied as shown on the 13.5 mm thick plate. P = 100 kN. Holes are oversized causing all rivets to always proportionately react to load applied on the plate. 1. Which of the following most nearly gives the force in rivets if P is applied at the centroid of four(rivets)? a. 50 kN b. 30 kN c. 25 kN d. 40 kN 2. Which of the following most nearly gives the force in rivets if only moment equals P times e is applied at the centroid of four(rivets)? a. 12.567 kN b. 10.451 kN c. 32.672 kN d. 17.678 kN 3. Which of the following most nearly gives the maximum force in rivets due to combined effect of P and torque? a. 42.28 kN b. 40.93 kN c. 39.53 kN d. 37.34 kN 4. Considering shearing in bolts, what is the minimum required diameter if allowable shearing stress in bolts is Fv/2, Fv = 372 MPa a. 27.34 mm b. 14.53 mm c. 16.45 mm…
This arm is attached to a wall on the left. The right end is free hanging. Each section is 2.0m wide and 3.0m high. If the force at the end of the arm is F = 200.0N, what is the force in member 9? Use the Method of Sections. Use a positive number if it is in tension and a negative number if it is in compression.

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L