Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the contact surfaces. The glue to be used can safely provide a shear strength of 125 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 14 kips. Note that a gap of 0.5 in. is required between boards (1) and (2). L 6 in. (1) 17.77 in. 14.05 in. 19.17 in. 12.43 in. 22.42 in. 0.5 in. (2)

Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the contact surfaces. The glue to be used can safely provide a shear strength of 125 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 14 kips. Note that a gap of 0.5 in. is required between boards (1) and (2). L 6 in. (1) 17.77 in. 14.05 in. 19.17 in. 12.43 in. 22.42 in. 0.5 in. (2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a beam made of the same material by five rivets that are made of a steel with Sy=300 MPa and Sut=365 MPa. The thickness of the bracket and the beam are 12 mm and 16 mm respectively.Diameters of the rivets are 20 mm. What safe load F(steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
The plate shown is made of UNS G10350 cold drawn steel (Sy=460 MPa and Su=550 MPa),and is fastened to an I beam made of UNS G10150 cold drawn steel (Sy=320 MPa and Su=385 MPa) by four rivets made of a steel with Sy=300 MPa and Su=365 MPa. Thickness of the plate is 10 mm and thickness of the flanges of the I beam is 15 mm. Diameter of the rivets is 20 mm. What safe load F (steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
A laminated wood beam consists of eight 2.25 in. × 5.00-in. planks glued together to form a section b = 5.00 in. wide by d = 18 in. deep, as shown. If the allowable strength of the glue in shear is 105 psi, determine(a) the maximum uniformly distributed load w that can be applied over the full length of the beam if the beam is simply supported and has a span of L = 19 ft. [Answer: w = 663.2 lb/ft]
All pins are in double shear, each has a diameter of 13mm, and the average shear stress in each pin is not to exceed 65 MPa. Determine the maximum magnitude P of the loads that the beam can support
A thrust collar that rests on a 0.75 in thick polymer plate supports the vertical nylon shaft shown below. The shaft has a diameter d = 0.50 in. The load acting acting on the shaft is P = 600lb. A) The ultimate shear strength of the nylon shaft is 2700 psi, and a factor of safety of 2.5 with respect to shear is required. Determine the minimum thickness t required for the thrust collar B) The ultimate bearing strength of the polymer plate is 2000 psi, and a factor of safety of 3.0 with respect to bearing is required. Determine the minimum outer diameter Dcollar required for the thrust collar.
The rigid beam is supported by a pin at C and an A992 steel guy wire AB of length 6 ft. If the wire has a diameter of 0.2 in., determine how much it stretches when a distributed load of w = 200 lb>ft acts on the beam. The wire remains elastic.
In the graft, the 6-meter-high arm is manufactured using the l profile given below. It is fixed to both ends of the arm with a built-in support. If the yield strength of the material is σy=400 MPa Elasticity modulus E=2*105 MPa If the safety factor used in the design is 2.5, the arm in question is What is the highest axial load it can safely carry?
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
The anchor opposite is made of Cr-Ni steel. Thereelastic limit is 520 Mpa. What should be the minimum diameter inanchor shear if the load F is 50kN? Consider a safety factor of 2.Please note that the safety factor is applied tothe elastic limit.
The strut is supported by a pin at C and an A-36 steel (Young’s Modulus is 200 GPa) guy wire AB. If the wire has a diameter of 5 mm, determine how much it stretches when the distributed load acts on the strut. W0=11Kn/m
A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq at an angle of 30 deg with the horizontal. The allowable stresses on the glued joint in tension and shear are 5MPa and 3MPa respectively. Determine the largest load P. Assume that the strength of the glued joint controls the design. The cross-sectional area of the bar is 225 mm^2.
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]