Two beams A and B are simply supported, subjected to identical loads. The two beams have same width, but depth of beam A is double the depth of beam B. The ratio of their section modulus is (a) 2 (b) 3 (c) 4 (d) 8

Two beams A and B are simply supported, subjected to identical loads. The two beams have same width, but depth of beam A is double the depth of beam B. The ratio of their section modulus is (a) 2 (b) 3 (c) 4 (d) 8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming…

Q: Determine the member force BD (kN) shown in the figure. B 3 kN 2 m 45° 30 30 - 2 m 2 m - -

Q: The uniform beam of weight W is to be supported by the two rods, the lower ends of which were…

Q: In case of a simple supported rectangular beam of span L and loaded with a central load W, the…

Q: Nonprismatic Beams veered cantilever beam AB of length L has square cross sections and supports a…

Q: 2. The T section shown is the cross-section of a beam formed by joining two rectangular pieces of…

A: Given: a T section Maximum shearing…

Q: A rigid bar ABC is supported by three identical wires A, B, and C as shown in the figure. The bar…

A: Step 1 Equilbrium condition is applied Step 2 Taking moment about hinged point Step 3 compatibilty…

Q: Q.3.A tapering conical bar of 1 m length has diameter of 20 mm and 50 mm at the two ends. Find the…

A: Length of the bar = L = 1m. Diameter of the bar d1 = 20mm d2 = 50mm Tensile load = P = 250KN…

Q: The beam shown is subjected to a load P at its end. Determine the displacement at C. EI is constant.

A: The FBD of the beam is shown below:

Q: A beam of flexural rigidity EI is fixed at A and supported by a linear spring of stiffness k = EI at…

Q: Determine the value of Ely midway between the supports for the beam loaded as shown below 200 N/m M…

Q: The cross-section and loading condition of a simply supported beam is shown in figure. The allowable…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: A simple beam is subjected to two concentrated loads as shown. The beam section is a rectangular…

A: Strain energy = 4P2L33EI

Q: The truss shown is acted upon by two forces. The 223 kN force acting at Joint A and the 100 kN force…

Q: The copper shaft is subjected to axial loads shown below. Determine the displacement of end A with…

A: Displacement: - It is defined as the distance moved by any section with respect to its Centre of…

Q: A wooden beam carries the loading shown. Determine the smallest allowable width b of the beam if the…

Q: The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that…

Q: A steel column of length 6 m forms part of a support structure and is subjected to an axial…

A: It is required to determine the area. A=BD-bd=75 mm×125 mm-67.5 mm×110 mm=1950 mm2 It is required to…

Q: A hollow steel shaft has length of 4 meters with a circular cross-section. The outer and inner…

Q: 6.83 The span of a cantilever beam is 2 m. The cross- section of the beam is a hollow square with…

A: Given data- span of the beam L=2 m=2000 mmsides of square=100 mmMoment of inertia I=4×105 mm4bearing…

Q: A simply supported beam having a rectangular cross section. If the height of th etion is three times…

A: To find dimension of section

Q: Ex Dotermine reaction 420N 800 N Components at A and B for the beam shown, Weight t Hinge Rollar of…

A: Given The above figure in ist example with load and their distances and also self weight = 600N

Q: 2. The simply supported wood beam ABC in Fig. (a) has the rectangular cross section shown. The beam…

Q: A simply supported beam is loaded by the couple M=2000 N-m as shoWH. TAE beam has a channel-type…

Q: rigid support @ A A 400 N-m 850 N-m L=1.4 m 30 mm diameter L=2.4 m 50 mm diameter L=1.9 m 30 mm…

Q: Member BC with a weight of 1000lb is subjected to a uniform load of 300lb/ft as shown.Determine the…

Q: Figure 1 shows the cross-section of a lightly welded steel column under axial compression. The yield…

A: (a) The width of the flange is bf = 450 mm. The thickness of the flange is tf = 12 mm. The thickness…

Q: The inverted T-beam supports three concentrated loads as shown in the figure. Find the maximum…

A: ASKED: To determine the maximum allowable value of load P for the given allowable stresses in…

Q: An 8-m simply supported beam carries a concentrated load of 40 kN at a distance of 3.25 m from the…

A: To find deflection under maximum bending moment

Q: A horizontal cantilever beam, made of steel, is pin-jointed with a vertical brass rod at the end B,…

A: Given data Modulus of elasticity Length Diameter Loading Deflection

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

Q: of the beam

A: Given data As=8-25mm bars (fy=350MPa) depth=500mm

Q: For the exact in the figure tensile strength = 8000 N/ cm ^ 2 compression safety = 3000 N / cm ^ 2…

A: The given data is: Allowable tensile strength is given as: σt,allow=8000 N/cm2 Allowable compressive…

Q: Calculat reactions at pin support A and edge B, take beam weight 35 Kg 1 т 3 m B 50° A

A: For calculating the reactions equilibrium conditions must be followed: Sum of all the forces among…

Q: (a) Derive the equation of the elastic curve for the simply supported beam that is loaded by the…

A: To find equation of elastic curve

Q: Determine (a) the bending stress at point H. (b) the bending stress at point K. (c) the maximum…

Q: 200 N.m couple M is applied to a T beam section shown in figure. Determine (a) the stress on the…

Q: An 8-m simply supported beam carries a concentrated load of 40 kN at a distance of 3.25 m from the…

A: Calculate deflection at point of maximum moment

Q: *Prob. 2.3-9. A “rigid" beam AD is supported by a smooth pin at D and by vertical rods attached to…

A: We have to determine the value of the beam angle theta that corresponds to the strain and the…

Q: Determine the force of member CG. Include a negative sign if the answer is in compression. Indicate…

Q: 2.31 The three symmetrically placed rods support the rigid block of mass M. Before the block was…

Q: the required maximum value of and the corresponding position of the beam, (b) the final position of…

A: A rigid steel beam is given to determine Maximum value of Q final position of beam

Q: a) Determine the minimum moment of inertia. b) Determine the maximum moment of inertia. e) Determine…

A: For the maximum and minimum Moment of Inertia, concept of Stress Transformation can be used.

Q: *Prob. 2.3-9. A “rigid" beam AD is supported by a smooth pin at D and by vertical rods attached to…

Q: A beam is given as shown. Width of the beam is 100 mm and depth is 250 mm. Determine the maximum…

A: answer = 26.4 Nmm2explanation is given in below step

Q: Question 5 The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the…

Q: A cantilever beam with length L = 4 m carries a concentrated load P =26 kN at the free end. The beam…

Q: B) Determine the Resultant of the parallel, coplanar force system force system showed in Figure 6.…

A: Given Three coplanar, parallel forces

Q: The stiffnesS of spring A and B are K and 2K respectively. If each spring is subjected to load 'p'…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

I need the answer as soon as possible

Two beams A and B are simply supported,
subjected to identical loads. The two beams
have same width, but depth of beam A is
double the depth of beam B. The ratio of
their section modulus is
(a) 2
(b) 3
(c) 4
(d)
8.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A uniform load of 8 kN/m acts on segment BC of the rigid beam shown. The beam is supported by a steelrod BD having a cross sectional area of 200 mm2. Determine the vertical displacement of the beam at Cafter the distributed load is applied. For steel, E = 200 GPa. Neglect the weight of the beam. Express youranswer in mm.
The simply supported beam of length L carries a uniformly distributed load of intensity w0 overthe span of the beam. Determine (a) the equation of the elastic curve, and (b) the maximumdisplacement.
Find the maximum uniform load w kN/m that can be applied on the beam shown in figure. so that the beam will not be cracked. Use n = 8.6 and fr = 3.4 MPa. Neglect the beam weight.
A reinforced concrete column 500 mm × 500 mm in a section is reinforced with 4 steel bars of 25 mm diameter; one in each corner, the column is carrying a load of 1000 KN. Find the stress in the concrete and steel bars. Take E for steel = 210×10^3N/mm2 and E for concrete = 14×10^3 N/mm2
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. a. What is the moment of inertia (in mm4) of the cross-section of the beam? b. What is the value of Q (in mm3)? c. What is the actual bending stress of the beam in MPa? d. What is the actual shearing stress of the beam in MPa?
The rigid beam is suspended from two steel rods as shown and is initially horizontal. BF bar with a cross section of 143 . The midpoint of the beam is deflected 10 mm downward by the slow application of the force , after which the force is slowly removed. Knowing that the steel used for the rods is elastoplastic with and determine (a) the required maximum value of and the corresponding position of the beam, (b) the final position of the beam.
Part 2. Show Complete solution and appropriate free body diagram.The uniform beam weighs 200 kg and carries a 500 kg crate as shown. Determine the reaction at the support at A and B.
STRENGTH OF MATERIALS (NO LONG EXPLANATION NEEDED) PLEASE WITH FBD! RATE WILL BE GIVEN For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to load P = 40 kN. The rods are identical except for their lengths. Find the (a) stress in rod A if its cross-sectional is 300mm2 (b) If rod A elongates by 2mm, how much is the elongation of rod B?
Design of Beam in Flexure Use Working Stress Method Fc=10 MPa Fs=120 MPa n=12 Bar Diameter = 20 mm Take b=d/2
A rigid bar ABC is supported by three identical wires A, B, and C. The bar ABC is horizontal before the load P is applied. Assume the bar and the wires are weightless. Determine the tension in wire B if P = 1200N
Determine the largest weight W that can be supported by the two wires AB and AC. The allowable working stresses are 180 MPa for AC and 120 MPa for AB. The cross-sectional area of AB is 500 mm2 and that of AC is 300 mm2. Show the solution. Correct answer is 60.23kN
A beam is supported by a column 3 m tall with dimensions a x 1.5a as shown above. The column is fixed at the base and pinned to the beam. Assume a Young’s modulus of ? = 25 GPa and yield strength of ?? = 20 MPa for the column.a) Draw the SFD and BMD for the beam and determine the axial load acting on the column.b) What is the minimum value of “a” that would not result in buckling of the column?c) If the column was instead fixed to the beam, how would this change the minimum value of “a”?