• Part G - Part GWhen slipping is about to occur what is the friction force on Block B, otherwise known as FB?Express your answer in units of N to three significant figures and include the appropriate units.Vol A£o n vec?FB =NSubmitRequest AnswerPart H - Part HWhen slipping is about to occur what is the normal force on Block B, otherwise known as Ng?Express your answer in units of N to three significant figures and include the appropriate units.Hνα ΑΣφ?vecNB =NSubmitRequest Answer Two blocks A and B, each having a mass of 7 kg , are connected by pins using the linkages shown.ВА0201CThe coefficient of static friction between Block A and the floor is HA = 0.2.The coefficient of static friction between Block B and the floor is µB = 0.41.The angles given are01 = 45 degrees02 = 25 degreesNeglect the weight of the links.i. Draw the Free Body Diagrams for pin C, Block A, and Block B.ii. Applied force P on pin C is gradually raised. Which block starts slipping first and what is the value of P when slippage starts occurring?Hint: It helps to establish two cases, one in which block A slips and one in which block B slips, and then calculate what occurs in each case in order to determine what happens.

Two blocks A and B, each having a mass of 7 kg , are connected by pins using the linkages shown. B А 02 01 C The coefficient of static friction between Block A and the floor is µ = 0.2. The coefficient of static friction between Block B and the floor is µR = 0.41. The angles given are O = 45 degrees O2 = 25 degrees Neglect the weight of the links. i. Draw the Free Body Diagrams for pin C, Block A, and Block B. ii. Applied force P on pin C is gradually raised. Which block starts slipping first and what is the value of P when slippage starts occurring? Hint: It helps to establish two cases, one in which block A slips and one in which block B slips, and then calculate what occurs in each case in order to determine what happens.

Two blocks A and B, each having a mass of 7 kg , are connected by pins using the linkages shown. B А 02 01 C The coefficient of static friction between Block A and the floor is µ = 0.2. The coefficient of static friction between Block B and the floor is µR = 0.41. The angles given are O = 45 degrees O2 = 25 degrees Neglect the weight of the links. i. Draw the Free Body Diagrams for pin C, Block A, and Block B. ii. Applied force P on pin C is gradually raised. Which block starts slipping first and what is the value of P when slippage starts occurring? Hint: It helps to establish two cases, one in which block A slips and one in which block B slips, and then calculate what occurs in each case in order to determine what happens.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.63P: The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The...

See similar textbooks

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The 600-lb cable spool is placed on a frictionless spindle that has been driven into the ground. If the force required to start the spool rotating is F = 160 lb, determine the coefficient of friction between the ground and the spool. Neglect the diameter of the spindle compared to the diameter of the spool.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The 120-kg block A is suspended from a rope that runs around the fixed pegs B and C. The coefficient of static friction between the pegs and the rope is 0.25. Determine the range of the force P for which the system is in equilibrium.
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
A block with a mass of 100 kg (left-block) is connected to another block of mass M (right-block) by a cable that passes over a fixed drum as shown below. The coefficient of static friction between the left-block and the floor is 0.45, between the right-block and floor is 0.4, and between the cable and the fixed drum is 0.25. Ignore tipping (overturning). Determine the minimum mass of the left-block for which motion does not occur.
Six 5 N blocks are stacked vertically. The coefficient of static friction between the blocks is µs = 0.20. Determine the horizontal force that must be applied to the fifth block from the top of the stack, in order to slide it out without moving the other blocks.
The 150 lb block rests on an inclined surfacevand is attached to a frictionless pulley C. The coefficient of static friction between the block and the incline is 0.25. The dope passes over a drum D, where the coefficient of static friction between the rope and the drum is 0.2, as shown. Find the minimum and maximum values for the weight of block B, Wb, for which no motion will occur. Neglect tipping.