Two cables of different materials have an initial length of 1 m and a cross-sectional area of 2x10 m² . If a tensile force of 1000 N acts on both cables, their lengths increase by 2 cm and 5 cm, respectively. Determine the relation between the Young's modulus of both cables. O Y, = 3.5Y, O Y, = 3.5Y, O Y, = 2.5Y, O Y = 2.5Y,

Two cables of different materials have an initial length of 1 m and a cross-sectional area of 2x10 m² . If a tensile force of 1000 N acts on both cables, their lengths increase by 2 cm and 5 cm, respectively. Determine the relation between the Young's modulus of both cables. O Y, = 3.5Y, O Y, = 3.5Y, O Y, = 2.5Y, O Y = 2.5Y,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum tensile force that can be applied on a member of diameter 25cm and tensile strength 168kPa.
A force of 5 KN is exerted on a 6 mm diameter brass rod. Determine the percentage increase of its length if the modulus of elasticity of brass is 90 GPa.
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 80 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 2 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
The deck of a bridge is made up of 12 mm thick steel plates 2 m long by 1·2 m wide. Under load, the plate is subject to tensile forces of 7·5 kN longitudinally and 6 kN across the width. Determine the change in the thickness of the plate under this load regime. Modulus of elasticity = 210 GN/m² and Poisson’s ratio = 0·3
The bar shown below is tested in universal testing machine. It is observed that at a loadof 40 kN the total extension of the bar is 0.280 mm. Determine the Young’s modulus of thematerial.
A stepped circular bar having diameter 20 mm, 15 mm and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm, respectively, is subjected to an axial tensile force of 5 kN.If E = 100×103 N/mm2and Poisson’s ratio v = 1/m = 0.32 for the material of the bar, determine a) Total change in length.b) Change in each diameter.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (sY)st = 640 MPa, and for the bronze (sY)br = 520 MPa,determine the magnitude of the largest elastic load P that can be applied to the assembly. Est = 200 GPa, Ebr = 100 GPa.
The weight is suspended from steel and aluminum wires, each having the same initial length of 3 m and cross-sectional area of 4 mm2. If the materials can be assumed to be elastic perfectly plastic, with (sY)st = 120 MPa and(sY)al = 70 MPa, determine the force in each wire if the weight is (a) 600 N and (b) 720 N. Eal = 70 GPa, Est = 200 GPa.
. A 175-lb woman stands on a vinyl floor wearing stiletto high-heel shoes. If the heel has the dimensions shown, determine the average normal stress she exerts on the floor and compare it with the average normal stress developed when a man having the same weight is wearing flat-heeled shoes. Assume the load is applied slowly, so that dynamic effects can be ignored. Also, assume the entire weight is supported only by the heel of one shoe. Solution: - For Stiletto shoes =869 psi - For Flat-heeled shoes =50.5 psi
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.