Please help me answer this mechanical engineering question Two cylinders of mass m₁ and m₂ are atequilibrium in the position shown. If m₂ = 20kg, determine the tension in cable A, cable B,and the magnitude of m₁.ABm₁40°C30⁰m2Work in SI units of N, kg, m, s but do not enterunits in your answers. Answers should have 3significant figures. Question 1Determine the tension in rope A.Question 2Determine the tension in rope B.Question 3Determine the magnitude of m₁.

Answered: Image /qna-images/answer/60ba03bc-9de1-44cb-866a-8e0dfa7a94f8.jpg

Two cylinders of mass m₁ and m₂ are at equilibrium in the position shown. If m₂ = 20 kg, determine the tension in cable A, cable B, and the magnitude of m₁. A B m₁ 40° C 30° m2 Work in SI units of N, kg, m, s but do not enter units in your answers. Answers should have 3 significant figures.

Two cylinders of mass m₁ and m₂ are at equilibrium in the position shown. If m₂ = 20 kg, determine the tension in cable A, cable B, and the magnitude of m₁. A B m₁ 40° C 30° m2 Work in SI units of N, kg, m, s but do not enter units in your answers. Answers should have 3 significant figures.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A smooth inclined plane has a gradient of 1 in 6. Calculate the mass of a body that can be held in equilibrium on the plane by a force of 80 N when the force acts: (a) parallel to the plane answer M=49.62kg (b) horizontally answer M=48.94 kg (c) at an angle of the 20° with the plane. answer M=46.62kg
1. Samer (ms = 75 kg) is sitting on the seat of a swing at the playground. The seat is supported by two cables, one on each side of the seat. (You may assume the seat has negligible mass.) A. Determine the tension in each cable due to Samer sitting on the swing seat. B. Given each cable has a diameter of 1 mm and each cable is exactly 5 m long before Samer sits on the seat, determine the length of each cable when Samer is sitting on the seat. (The cables are made of Aluminum for which Y = 70 GN/m°.) show all work in logical, detailed form and box in numerical answers. Include a diagram wherever possible. On any problem where an FBD is appropriate, it must be included for maximum credit. All numerical results should be stated to 3.00 or 4.000 significant figures and in mks units unless otherwise noted.
The small piston of a hydraulic lift has a cross-sectional area of 3.00cm^2,and its large piston has a cross-sectional area of 200cm^2.What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg= 15.0kN?
Determine the magnitude and direction of the angle theta of the force FAB that must be exerted on bar AB to maintain equilibrium of the system. The suspended mass is 110 kg. Neglect the size of the pulley at A and treat all pulleys as smooth. What should happen to maintain the equilibrium of the system if FAB acts with an angle theta= 0°?Consider g = 9.81 m/s2.
An athlete of 60 kg and 1.70 m tall performs the ring exercise called "the Christ", in which he keeps his body immobile with his arms extended horizontally as shown in Fig.-Prob.17(a). The angle with the vertical of the cords from which the rings hang is theta = 10. (a) Determine the tension T in the cords holding the rings. (b) Considering each arm of the athlete as a rigid horizontal bar subjected to the forces indicated in Fig.-Prob.17(b), calculate the value of the components RX and RY, the value of the reaction “R” and of the beta angle.- W is the weight of the arm, applied in the middle of its length.- R is the reaction at the shoulder joint O.- RX and RY are the horizontal and vertical components respectively of the reactionapplied at the shoulder joint O.- Note: Consider that the mass of each arm of the athlete is 3% of the total mass, and thatthe length of the arm is equal to 35% of its height. Fig.-Prob.17(a): Man performing the position of "The Christ"Fig.-Prob.17(b):…
I need your help expert. The system shown below is in equilibrium. Spring 3 is known to have a change in length of 10 cm. The magnitude of the compressive force in Spring 2 is 15% more than the magnitude of force P, while the magnitude of the compressive force in Bar 1 is 100 N less than that in Spring 2. If the spring constants of Springs 2 and 3 are 625 and 1200 N/m, respectively, determine the following: a. magnitude of forces P (in N) and F (in N) b. tension (in N) in cable ABC c. mass (in kg) of Block A d. compressive force in Bar 1 e. change in length (in cm) of Spring 2 Draw the complete FBD’s of Block A, Hook C and Pulley E. (Note: Below are the final answers, kindly match your answer on this. Thank you) Answer: P = 131.2831 N, F = 87.1569 N, TABC = 110.7024 N, mA = 15.6338 kg, F1 = 50.9756 N, s2 = 24.1561 cm
The hanging mobile pictured above consists of two masses, m1 and m2, suspended from a uniform 10 cm long rod, which is in turn suspended from the ceiling at an angle of 70 as pictured above. The mass m1 is 0.02 kg, while the mass of the rod is mr = 0.01 kg. Assuming the mobile is in a state of static equilibrium, find the value of mass m2.
The uniform plate has a weight of W = 450 lb. Suppose that F= 250 lb. The plate is supported by cables A, B, and C as shown below. Determine: A) The tension in the supporting cable A. B) The tension in the supporting cable B. C) The tension in the supporting cable C.
Two spheres, one heavier and weighing12000 N and of diameter 1.2 m and the other lighter and weighing 4000 N, are tied with a rope and placed in seawater. The density of sea water is 1025 kg/m^3. It was found that the spheres floated vertically with the lighter sphere just under the water PROBLEM 0surface. Illustrate the problem before answering the following questions:a)Determine the diameter of the lighter sphere in meters.b) Determine the tension in the rope in Newtons.
Springs OA and OB are originally unstretched in a vertical position. Find the horizontal force, F, when the springs are held in the position as shown, given: k = 550 lb/ft, L1 = 0.6 ft, L2 = 1.3 ft
A crane is used to lower weights into the sea (density = 1,025 kg/m3) for an underwater construction project. Determine the tension in the rope of the crane due to a rectangular 0.4m x 0.4m x 3m concrete block (density = 2,300 kg/m3) when it is completely immersed in water.
If F1 = 390 N force is applied to the piston with d1 = 4 cm diameter, what is the magnitude of the force F2 that can be resisted by the piston with d2 = 10 cm diameter? Neglect the weights of the pistons.