Two cylindrical hollow shafts with shear modulus G = 77 GPa are welded together to a rigid connecting plate. A torque at C causes the connecting plate to rotate 8'. Find the maximum shear stress in each shaft. Diameter AC = 30 cm Diameter CB = 20 cm 10.5cm, Acm y 4=6m G L2=4m

Two cylindrical hollow shafts with shear modulus G = 77 GPa are welded together to a rigid connecting plate. A torque at C causes the connecting plate to rotate 8'. Find the maximum shear stress in each shaft. Diameter AC = 30 cm Diameter CB = 20 cm 10.5cm, Acm y 4=6m G L2=4m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.2.6P: A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius...

See similar textbooks

Related questions

Q: A cylindrical shaft made of steel of yield strength 700 MPa is subjected to static loads consisting…

A: Givenσy=700 MPaτ=σyF.S×0.58=7002.1×0.58=193 MPaM=10 kN=10000 NT=30 kN=30000 N

Q: .9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the…

A: GIVEN DATA- SHEAR STRESS IN BRONZE SHAFT =100MPa DIAMETER OF BOTH SHAFT =120mm G FOR STEEL=83GPa G…

Q: An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft…

A: Find the maximum shear stress in shaft 1.

Q: A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2 = 1.0…

A: Solution; Note: The stress concentration factor kt values are taken from the stress concentration…

Q: Gears b and c have diameters of 10 cm and 4 cm, respectively. The maximum shear stress supported by…

A: Tmax=550kgf/cm2G=8×105kgf/cm2

Q: The ice weighs 5 kg and is 30 cm wide across the tongs. The distance between the handles is 12 cm…

Q: . A two cell tube made of Aluminum (E = 70GPa) as shown in the Fig (2) and subjected to a Torque…

A: Write the given data. E=70 GPaT=90000 NcmFor Aluminium, μ=0.3 Calculate the modulus of rigidity.…

Q: Q2 A solid circular bar ABC consists of two segments, as shown in figure 2. One segment has diameter…

A: The diameter of the shaft can be determined by two criteria 1) Shear stress 2) Angle of twist Both…

Q: Calculate the shaft diameter and torsion angle since the maximum torsional moment is 150 Nm for a 1…

Q: Two shafts are connected by gears. The diameter of the two shafts is 1.5 in. They have the same…

A: Given: Diameter of two shafts (D)=1.5in or 0.125ftShear modulus G=11.2×106Radius of gear E=4in or…

Q: A hollow shaft (k = 0.4) is subjected to a bending load of 500 N, and a torsion moment of 275000…

Q: The internal loadings at a critical section along the steel drive shaft of a ship are calculated to…

A: Given data: The torque, T = 2300 lb-ft. The bending moment, M = 1500 lb-ft. The axial trust, P =…

Q: (a) the maximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106…

Q: Determine the maximum shear stress (in ksi). AT = 654 lb ft Diameter =3.7 in J =1.5in4 G = 11,000…

Q: An aluminum tube of outer diameter R,- 50 mm is heated such that it is mounted over a steel shaft of…

A: For solution refer below images.

Q: A steel propeller for a windmill transmits 5 kW at 87.9 rpm. If the allowable shear stress in the…

Q: A solid 1.375 in. diameter shaft is subjected to a torque of T = 340 lb ft and an axial load Pacting…

Q: A 12 mm The steel shaft is made from two segments: AC has a diameter of 12 mm, and CB has a 125 mm D…

A: According to the information we have a steel shaft with two segments AC and CB torque on the shaft…

Q: A B E F 20 kN-m 35 kN-m 85 kN-m 30 kN-n

A: given d=0.2m = 200mm so r = 100mm

Q: A thin wall spherical tank of diameter 1.5 m and wall thickness 65 mm has internal pressure of 20…

Q: Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure ,…

A: Write the torque developed on the taper shaft. T=20 kN·m=20 kN·m×1000 N·m1 kN·m=20×103 N·m Write…

Q: A cylindrical metal tube of mean radius r = 5 in., length L = 14 ft, and shear modulus G = 11 x 106…

Q: A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2…

Q: A and B points are flush mounted. Since the maximum shear stress is = 10N / mm ^2 in the section…

Q: An impeller mechanism in a granular material mixing tank is shown. The shaft is hollow with a 2.25"…

A: Given, ro = 2.25" θmax=6o τmax=10 ksi G = 11000 ksi

Q: 4 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C,…

Q: A 24 mm diameter shaft 0.8 m long is twisted through an angle of 1.8 degrees. What is the stress…

Q: The concrete post (Ec5 3.6 3 106 psi and αc5 5.5 3 10–6/°F) is reinforced with six steel bars, each…

A: Given.diametre of steel bars=d=78 inArea of steel bars,As=6×(π4×d2)⇒As=6×[π4×(78)2] ⇒As=3.6078…

Q: A 1.00 in. diameter solid steel shaft supports loads PA = 75 Ib, Pc = 135 lb, and PE = 50 lb. Assume…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 12.25 in. and…

Q: The rectangular cross section ABCD shown below has a circular cutout of diameter d= 50.0 mm through…

A: From the given data,

Q: The compound shaft is composed of bronze cylindrical segment AB and steel cylindrical segment BC.…

Q: A solid circular torsional member OPQ is subjected to torsional moments as shown in the figure (not…

A: GIVEN DATA- A STEPPED SHAFT GIVEN WE HAVE TO FIND MAXIMUM SHEAR STRESS IN SHAFT

Q: A concentrated load of P = 20 kN is applied to the upper end of a pipe with length L = 5 m. The…

Q: the cross-stctions e-e and f-f, respectively, when a torque T = 800 Nm is applied at point B. Take…

Q: A thin wall spherical tank of diameter 1.5 m and wall thickness 65 mm has internal pressure of 20…

Q: A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800…

Q: In the solid circular section bar with radius R=10mm in the figure, due to the given loading, Find…

Q: A solid shaft with a constant cross sectional area is subjected to twisting moment as shown. The…

Q: Consider a tube having a rectangular cross-section as shown below. The tube is subject to two…

A: Since you haven't provided a diagram related to the question. I've found it on the web which is…

Q: 6. A leather belt, 125 mm wide and 6 mm thick, transmits power from a pulley 750 mm diameter which…

Q: For the figure shown below. Find the maximum allowable value of P if the bending stresses are not…

Q: A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50…

A: Given Data, T = Torque transmitted by the solid shaft = 600 Nm = 600 x103 Nmm ?max= Maximum shear…

Q: The copper shaft (G= 44 GPa) is bonded to A the aluminum shaft (G= 26 GPa) at B point and their…

A: Given, Modulus of rigidity of copper,G=44GPaModulus of rigidity of aluminium,G=26GPaLength of AB,…

Q: In the solid circular section bar with radius R=10mm in the figure, due to the given loading, Find…

Q: 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the .9 The compound…

A: Answer: The angle of rotation of the free end is 16.3°.

Q: Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

3. Two cylindrical hollow shafts with shear modulus G = 77 GPa are welded together
to a rigid connecting plate. A torque at C causes the connecting plate to rotate 8.
Find the maximum shear stress in each shaft.
Diameter A C = 30 cm
Diameter CB = 20cm
0.5cm
1 cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A thin-walled steel tube of rectangular cross section (see figure) has centerline dimensions b = 150 mm and h = 100 mm. The wall thickness t is constant and equal to 6.0 mm. Determine the shear stress in the tube due to a torque T = 1650 N · m. Determine the angle of twist (in degrees) if the length L of the tube is 1.2 m and the shear modulus G is 75 GPa.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A stepped shaft consisting of solid circular segments having diameters D1= 2.0 in, and D2= 2.4 in. (see figure) is subjected to torques T. The radius of the fillet is R = 0,1 in. If the allowable shear stress at the stress concentration is 6000 psi, what is the maximum permissible torque Tmax?
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.