PLEASE ANSWER NUMBER 3.9 MECH 222: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS. 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in theThe compound shaft consists of bronze and steel segments, both havingbronzesegment, determine the angle of rotation of the free end. Use G = 83 GPa forsteel and G = 35 GPa for bronze.BrNeT.Steel60 mm120 mm804 m3 mFIG. P3.10FIG. P3.93.10 The stepped steel shaft carries the torque T. Determine the maximum allow-able magnitude of T if the working shear stress is 12 MPa and the rotation of the freeend is limited to 4°. Use G 83 GPa for steel.

Answer: The angle of rotation of the free end is 16.3°.

120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the .9 The compound shaft consists of bronze and steel segments, both having oronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. %3! Brne Steel 45m 80i 120mm 3 m 3.5 m FIG. P3.10 FIG. P3.9

120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the .9 The compound shaft consists of bronze and steel segments, both having oronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. %3! Brne Steel 45m 80i 120mm 3 m 3.5 m FIG. P3.10 FIG. P3.9

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.19P: A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the...

See similar textbooks

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
Q2. A mild steel shaft transmits 21 kW at 250 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa.
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50 N/mm2, the minimum diameter of the shaft is
A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube?
A 3-meter solid steel shaft, with an unknown diameter, twists by 5° as it experienced a shear stress of 60 MPa. What is the diameter of the solid steel shaft? Use G = 83 GPa.
An aluminum thin‐walled tube of hollow rectangular cross‐section, Figure 1,is subjected to a torque of magnitude, T = 15360 N.m. If the tube lengthis, L = 1 m , and the shear modulus of aluminum is, G = 28 GPa.1. Determine the total angle of twist of the one‐meter long tube.2. Determine the shear stresses on the walls of the tube cross‐section.Where does the maximum shear stress occur?
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube is r1 = 45 mm and the measured angle of twist betweenthe ends is 0.5°, what is the shear strain γ1 (in radians) at the inners surface? b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to bekept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius(r2)max?
A composite shaft shown, composed of a steel (G = 77 GPa) core inside an aluminum (G = 25 GPa) jacket, carries a torque, T = 10 kN-m. The shaft is designed such that the aluminum jacket will fail first upon the application of the torque. 1) If the allowable shear strength of aluminum is 45 MPa, determine the minimum thickness, t, of the aluminum jacket, that can carry the torque.2) What must be the minimum shear strength of steel such that the aluminum jacket will fail first?3) Determine the maximum angle of twist that can be applied to the shaft.