Two different lathes turn shafts to be used in electricmotors. Measurements made of their diameters (in cm)areLathe A: 1.42 1.38 1.40 1.41 1.39 1.44 1.36 1.42 1.40Lathe B: 1.47 1.31 1.56 1.33 1.29 1.46 1.28 1.51Construct two stem-and-leaf diagrams to see if youshould suspect that the two lathes are turning out shaftsof different diameters.

Two different lathes turn shafts to be used in electricmotors. Measurements made of their diameters (in cm)areLathe A: 1.42 1.38 1.40 1.41 1.39 1.44 1.36 1.42 1.40Lathe B: 1.47 1.31 1.56 1.33 1.29 1.46 1.28 1.51Construct two stem-and-leaf diagrams to see if youshould suspect that the two lathes are turning out shaftsof different diameters.

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter64: Volumes Of Spheres And Composite Solid Figures

Section: Chapter Questions

Problem 28A: Compute the number of cubic centimeters of material in the locating saddle shown. Round the answer...

See similar textbooks

Similar questions

Refer to the plate shown in Figure 117 and determine the following distances. All dimensions are in inches. a. The horizontal center distance between the 0.265" diameter hole and the 0.150" diameter hole. b. The horizontal center distance between the 0.385" diameter hole and the 0.150" diameter hole. c. The distance between edge A and the center of the 0.725" diameter hole. d. The distance between edge B and the center of the 0.385" diameter hole. e. The distance between edge B and the center of the 0.562" diameter hole.
The distance between the centers of two holes can be checked with a vernier caliper. The position of the caliper in measuring the inside distance between two holes is shown in Figure 29-10. To determine the setting on the caliper, subtract the radius of each hole (one-half the diameter) from the center distance. In Exercises 19 through 23, give the hole diameters and the distances between centers. For each, determine (1) the main scale setting and (2) the vernier scale setting. All dimensions are in inches.
The distance between the centers of two holes can be checked with a vernier caliper. The position of the caliper in measuring the inside distance between two holes is shown in Figure 29-10. To determine the setting on the caliper, subtract the radius of each hole (one-half the diameter) from the center distance. In Exercises 19 through 23, give the hole diameters and the distances between centers. For each, determine (1) the main scale setting and (2) the vernier scale setting. All dimensions are in inches 23. Note: Hole tolerances and center distance tolerances are shown. Maximum and minimum vernier scale settings are required.
Determine diameters A, B, C, D, and E of the shaft in Figure 124. All dimensions are in millimeters. A=_B=_C=_D=_E=_
Compute the number of cubic centimeters of material in the locating saddle shown. Round the answer to the nearest cubic centimeter.
Four sets of equally spaced holes are shown in the machined plate in Figure 13-4. Determine dimensions A, B, C, and D to 2 decimal places. All dimensions are in millimeters. A=_B=_C=_D=_
Refer to the Decimal-Inch Spur Gears Table under the heading "Gearing-Diametral Pitch System" in Unit 48 to determine the pitch diameter of an 8-pitch gear that has 45 teeth.
Determine the maximum and minimum permissible wall thickness of the steel sleeve shown in Figure 29-15.All dimensions are in millimeters.
The surface of a soccer ball is composed of 12 regular pentagons and 20 regular hexagons. With each side of each regular polygon measuring 4.5 cm, the area of each regular pentagon is 34.9 cm2 and area of each regular hexagon is 52.5 cm2. a What is the surface area of the soccer ball? b If the material used to construct the ball costs 0.8 of a cent per square centimeter, what is the cost of the materials used in construction?