Two fixed plates being separated by thin plate with two vicious liquids μ₁ = 0.3 kg/(m.s) and µ₂ =0.5 kg/(m.s), respectively as shown in figure (1). The plate spacing h₁ =3 mm and h₂ = 2mm. The contact area between the plate and each fluid is 0.004 m². Assuming a linear distribution in each fluid, determine the terminal velocity V if the applied force F on the thin plat is ......... N. Use your last three digits of your ID for the applied force F...... N. 12 F.V. h₁ HI

Two fixed plates being separated by thin plate with two vicious liquids μ₁ = 0.3 kg/(m.s) and µ₂ =0.5 kg/(m.s), respectively as shown in figure (1). The plate spacing h₁ =3 mm and h₂ = 2mm. The contact area between the plate and each fluid is 0.004 m². Assuming a linear distribution in each fluid, determine the terminal velocity V if the applied force F on the thin plat is ......... N. Use your last three digits of your ID for the applied force F...... N. 12 F.V. h₁ HI

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A liquid a constant density 900 (kg/m3) is flowing at an unknow velocity V1 (m/det) through a horizontal pipe of inside diameter 10 (cm) and at pressure 5 (kg/cm2), and then it passes to a section of pipe in which the diameter is reduced gradually to 5 (cm) and the pressure is 3 (kg/cm2). Assumsing no friction losses, calculate the velocity V2 if the pressure difference is measured
Petrol (ρ=750 kg/m3) flows through a pipeline with inlet diameter 8 cm and outlet diameter 4 cm. The inlet and outlet gauge pressures measured to be 400 kPa and 130 kPa respectively. Assuming the pipeline to be horizontal and neglecting friction, calculate the outlet velocity (V2) of water by using continuity and Bernoulli’s equation.
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
Water (ρ=1000 kg/m3) flows through a pipeline with inlet diameter 10 cm and outlet diameter 5 cm. The inlet and outlet gauge pressures measured to be 400 kPa and 130 kPa respectively. Assuming the pipeline to be horizontal and neglecting friction, calculate the outlet velocity(V2) of water by using continuity and Bernoulli’s equation.
Airstream flows in a converging duct from a cross-sectional area A1=50cm2to across-sectional area A2=40cm2. If T1=300K, P1=100kPa, and V1=100m/s, find M2, P2,and T2.
For the velocity components (in cylindrical coordinates) u=-10(1-1/r2)cosθ, v=10(1+1/r2)sinθ, w=0 determine the expression of pressure for incompressible frictionless fluid flow in the absence of body force. Also check whether the equation of motion is satisfied or not.
1) When an incompressible fluid flows through a restricted (narrower) portion of a pipe, mass flow is preserved, so it: sloshes back and forth. must speed up. remains at constant speed slows down. creates a shock wave. 2) When an incompressible fluid moves from a wider pipe into a narrower one, it speeds up. This means that the wider portion must do work on the fluid (to accelerate it), and therefor the pressure there... goes to zero. is lower than in the narrow portion. is higher than in the narrow portion. is the same as in the narrow portion. cannot be calculated. 3) Normally, when the temperature of a solid, liquid, or gas increases, it expands, i.e., its volume V increases (and its mass density: ρ = m /V decreases). Because of its relatively strong hydrogen bonds, water ice forms an orderly, hexagonal lattice structure that requires the molecules to be about 9% further apart than when in the liquid phase, which…
A horizontal fan (such as that shown in example 5.24) pulls in stagnant air (ie. basically stationary air) atatmospheric pressure; the air approaches the fan outlet with speed 44 ft/sec (ie. 30 mph) and with static pressure 0.3 psi. The air flowing through the fan can be assumed to have a constant density of 2.4*10-3 slug/ft3. The air losses due to friction are 0.1 psi (or 6000 ft-lb/slug of air passing from the fan inlet to the outlet). a) Determine the shaft work in ft-lb/slug b) If the fan outlet area is 2 ft2, determine the rate of work on the air.
A constant-velocity horizontal water jet from a stationary nozzle impinges normally on a vertical flat plate that rides on a nearly frictionless track. As the water jet hits the plate, it begins to move due to the water force. Will the acceleration of the plate remain constant or change? Explain.
A wind tunnel has an incompressible flow of air, flowing horizontally from an inlet section, 7 times the test section. A u-tube is connected, having mercury inside. The mercury's specific weight is 1.33x10^5 N/m^3. Air condition at the inlet section is 1 atm and 280K respectively. Solve for the change in height inside the mercury if the velocity at the throat is 70m/s.
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
A fan draws air at rest and propels it 45 meters through a rectangular duct measuring 200 by 300 mm. At a rate of 0.6m3/s, air enters at 15°C and 750 mm Hg absolute pressure. What is the required theoretical power?