Two gage marks are placed exactly 250 mm apart on a 12-mm diameter aluminum rod. Knowing that, with an axial load of 5,114 N acting on the rod, the distance between the gage marks was recorded as 250.18 mm, determine the modulus of elasticity (GPa)of the aluminum used in the rod Use 2 decimals.

Two gage marks are placed exactly 250 mm apart on a 12-mm diameter aluminum rod. Knowing that, with an axial load of 5,114 N acting on the rod, the distance between the gage marks was recorded as 250.18 mm, determine the modulus of elasticity (GPa)of the aluminum used in the rod Use 2 decimals.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: A two-dimensional stress system has like stresses q=100 N/mm²ando,= 200 N/mm² in two mutually…

A: Given data- Stresses-σx=100 N/mm2σy=200 N/mm2To Find-The coordinates of the centre of the Mohr's…

Q: For the given vectors, determine the magnitude of the vector difference V₂-V₁ and the angle which it…

A: Given Data: The data is given as: V1=10 unitsV2=12 units The angle subtended by the vector V2 with…

Q: Osa 18° Taa /a 45° a 200 MPa 50 MPa

A: GIVEN: TO DETERMINE: The Normal stress on plane a-a CONCEPT: Angle substended by two planes on…

Q: The given two-dimensional flow with velocity, V=(x + 2y + 2)i +(4-y)j (a) compressible and…

A: Given: 2-dimensional flow velocity,V→=x+2y+2i^+4-yj^

Q: An intersection has a three-phase signal with the movements allowed in each phase and corresponding…

A: Given :

Q: The couple M = 23 kN-m is applied to a beam of the cross sec angle with the vertical. Determine the…

A: Given : M = 23 KNm and β =150 Find : stress at A, B ,D = ? Let the…

Q: horizontal th

A: solution of above problem is below:

Q: 1.3 The picture below shows a scale drawing of Bradley's three-bedroomed house. 3 cm 2,5 cm NOTE: 3…

A: The Detailed diagram is shown as below:- In the above figure, we have have stretch or extend the…

Q: Q5/ Derive an expression for the discharge over a sharp crested rectangular weir. A sharp edged weir…

A: Given values: A sharp crested rectangular weir. Normal flow, Q1 = 200 l/s = 0.2 m3/s Normal flow…

Q: A vertical curve was designed to connect intersecting tangents of grades of 4% ar - 6% for back and…

A: aWe knowOffset=Ax22L

Q: Question SITUATION. A steel channel is used as a purlin of a truss. The top chord of the truss is…

A: I have solved your problem

Q: Replace the force system acting on the pipe assembly by a resultant force FR and couple moment MR,…

A: Given:- The vector form of the force F1 = -25i^-15j^+25k^ lb The vector form of the force F2 =…

Q: cess if possible. Thanks!

Q: Calculate the velocity of flow in a 200-mm- diameter pipe when the quantity of flow is 40 li/sec.

Q: In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height…

Q: Water is flowing in a rectangular channel with a bed slope of 0.0005 ft/ft. The channel width is 10…

A: Given: Bed slope = 0.0005ft/lt rectangular channel width, B = 10ft Discharge , Q = 300cfs…

Q: iii) Determine the normal strain in wire AB if the lamp is applied to ring B, the ring moves to the…

A: Note:- In the question, only third sub-part is asked by the student so I am supposed to answer only…

Q: How are soils classified on the basis of shear strength? Draw the Mohr-Coulomb strength envelope…

A: Shear strength of soil is defined as the capacity of soil to resist shearing stress. It depends on…

Q: 800 lb/ft |A B C 9,000 lb-ft 3,600 lb D 600 lb/ft X E 1 in. 5 in.

Q: SITUATION I: A 50-m steel tape is of standard length under a pull of 5kg and a temperature of 22…

A: Given:Length of the steel tape,L=50 mPull load on tape, F1=5 kginitial temperature of tape, T1=22o…

Q: A 60-kg crate is lying on a horizontal plane. A pulling force P is applied to the crate by a rope…

A: Given :

Q: Describe one of the methods of measuring surface tension with a physical justification.

A: Given :surface tension To determine: method of…

Q: A car (automobile) manufacturer is designing a new bumper (fender). The material choice lies between…

A: These days, generally the materials used in common for car bumpers include polycarbonates,…

Q: Practical Part 25) Write the rod readings on each of the following rods. ស០៣-យ 23-4 21

A: I have solved your problem

Q: For a loaded cantilever beam of uniform cross-section, the bending moment along the length is M(x) =…

Q: The average surface area of a reservoir in the month of June is 20 km². In the same month, the…

Q: (d) Ca(HCO3)2 = 150 mg/L; Mg(HCO3)2 = 200 mg/L; CaSO4 = 180 mg/L; MgCl2 = 95 mg/L; CaCl2 = 137…

Q: 5. Derive the formula for the volume of the sphere using the principle of volumes of revolution.

Q: x(bar) = 13.1 mm AC150 x 19.3 is used as a boom to support the 15 kN load which is then mainly…

A: Solution: Given: Section C 150 x 19.3 load = 15 kN A = 2460 mm2 Ix = 7.20 x 106 mm4 Iy = 0.437x 106…

Q: How much will be the settling velocity of a spherical particle A (having specific gravity of 2.65)…

Q: [ 4k/ft 12 ft. -20 ft - - X3 - 60k 1 100 kft

Q: Compute the value the shear modulus G of steel whose modulus of elasticity E is 200 GPa and…

Q: 3. Design a square tied column of smallest cross section to carry an axial dead load of 900KN and…

Q: How much will be the settling velocity of a spherical particle A (having specific gravity of 2.65)…

Q: Question [1] In the figure below, the mass of the bucket is 5 kg. It is kept in equilibrium by the…

Q: A bar having the cross section shown has been formed by securely bonding brass and aluminum stock.…

A: Given data EAl = 70 GPA Eb = 105 GPA Allowable bending stress in aluminum = 100 MPa Allowable…

Q: Find the area of the region inside the cardiod r = 2 + 2 cosθ and the outside of the circle with r =…

Q: Which of the following statements is correct? O When a body moves along a circular path with a…

A: The acceleration is the change in velocity with respect to time. Let the velocity be v. Acceleration…

Q: The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to…

Q: A W310X86 beam with a yield stress of 345 MPa is simply supported over a span of 2.4 m and loaded…

A: I have solved your problem

Q: A historic race track is famous for its very steep banked track. The banked section of the track,…

Q: Calculate the shape factor of the built-up section formed by the channels and rectangular plates as…

Q: 9.79. A concrete conduit of cross-sectional area 10 ft² and wetted perimeter 12 ft carries water at…

A: at 50°Fν=1.410×10-5ft2sso,Re=vDνDh=4×AP=41012=3.33ftRe=83.3331.410×10-5Re=1889362 Flow is turbulant…

Q: What size pipe should be used to supply 1300 gpm so that the velocity does not exceed 3.0 ft/sec…

Q: A 90° conical vessel of height 2 m carries water whose volume is one half of the volume of the cone.…

A: Vortex flow Vortex flow describes how fluid moves along a curved route. The liquid will follow the…

Q: Determine the moment of the 3- kN force acting at A about point O. Also determine the moment of the…

A: position vectors A = 1.2i + 0j + 0.3k B = 0i + 0.5j + 0.4kThere vector AB = vector B - vector A=…

Q: Determine the scenario that will create the maximum shear force and bending moment on the beam.

Q: 20 KN/m 3m 3m 2m 15 KN . Determine the deflection midway between the supports. A. 15.25 mm B. 17.58…

A: Given beam:- Here,RA =Vertical reaction at point A RB=Vertical reaction at point B applying…

Q: 8.a. Equipment rated at 1200 A or more and more than six feet wide that contains overcurrent…

A: Given data- 8(a) 1200 A rating6 ft or more in width

Q: The following readings IS operation from points 1 to 12, (2.08, 1.625, 3.2, (1.67 and 2.74) CP, 218,…

Question

Two gage marks are placed exactly 250 mm apart on a 12-mm diameter
aluminum rod. Knowing that, with an axial load of 5,114 N acting on the
rod, the distance between the gage marks was recorded as 250.18 mm,
determine the modulus of elasticity (GPa)of the aluminum used in the rod.
Use 2 decimals.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in the cables are tightened until the stress in the cables reaches 60000psi. If the working compressive stress for the wood is 216psi. Determine the smallest permissible diameter of the pole.___________inches in 2 decimal places. Take note: Write it on a paper, hand written showing answer. Thanks
. Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in'the two materials must not exceed 50 MN/m 2 and 100 MN/m z respectively. [27.6, 19.5, 19.5, 13.8 ram.] Can you please show a full solution explaining what * means if you are using it thanks
Please show intermediate steps including free body diagrams, equations used, and problemsetup so that your approach can be followed. A nylon thread is subjected to a 2-lb tension force. Knowing that E = 0.5 x 10^6psi and that the maximum allowable normal stress is 6 ksi,determine (a) the required diameter of the thread, (b) the corresponding percent increase inthe length of the thread.
A tensile test was performed on a metal specimen with a diameter of 1⁄2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The data were plotted on a load-displacement graph, P vs. ∆L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P y∆L 5 1392 kips yin. What is the modulus of elasticity?
A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are symmetrically spaced and 20 feet long. The two outer wires are steel and the middle wire is brass. Calculate: a) Stresses in the wires
SHOW COMPLETE ANSWER AND ILLUSTRATION FINAL ANSWER IN 3 DECIMAL PLACES Problem 3: A steel wire 10 m long, hanging vertically supports a tensile load of 2 kN. 1. Determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 5 mm. Use E = 200 GPa. Neglect the weight of the rod. 2. Determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 5 mm. Use E = 200 GPa. Consider the weight of the bar and = 7,850 kg/m3
Define the terms shear stress and shear strain, illustrating your answer by meansof a simple sketch. Two circular bars, one of brass and the other of steel, are to beloaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) insingle shear, (b) in double shear, if the shear stress in the two materials must notexceed 50 MN/m2and 100 MN/m2respectively.
Determine the slenderness ratio and the Euler buckling load for round wooden dowels that are 3.00 m long and have a diameter of (a) 19 mm and (b) 29 mm. Assume E = 14 GPa. Answer:(a) Slenderness ratio = Pcr = N (b) Slenderness ratio = Pcr = N
Engineering Mechanics (Upvote will be given. Please write the complete solutions and FBDs Legibly. No long explanation needed. Solve in 3 decimal places.) Based on the problem and solution given (see the attached solution) , determine the shear stress in the grain of the timber column shown in the figure. (See the attached image)
calculate the corresponding depth uniform stress block in a reinforce concrete beam 42*10 deep reinforce with bars 20-mm in a diameter enclosed with 10-mm dia stirrups when the tensile steel strain is 0.008 and concrete compression strain 0.003. f'c = 22 Mpa. Express your anser in 2 decimal places only in mm.