Two gears of module (4 mm) have (28 and 38) teeth. The pressure angle is (20 ") and each gear has standard addendum of one module. Determine: 1. The length of arc of contact, 2. The maximum velocity of sliding if the pinion rotates at (150 r.p.m),

Two gears of module (4 mm) have (28 and 38) teeth. The pressure angle is (20 ") and each gear has standard addendum of one module. Determine: 1. The length of arc of contact, 2. The maximum velocity of sliding if the pinion rotates at (150 r.p.m),

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?
Two spur gears of 24 teeth and 36 teeth of 8 mm module and 20° pressure angle are in mesh. Addendum of each gear is 7.5 mm. The teeth are of involute form. Determine : 1. the angle through which thepinion turns while any pair of teeth are in contact, and 2. the velocity of sliding between the teethwhen the contact on the pinion is at a radius of 102 mm. The speed of the pinion is 450 r.p.m
In an epicyclical gear train of the sun and planet, the pitch circle diameter of the internally toothed ring is to be 224mm and the module 4mm. when the ring D is stationary, the spider, which carries three plant wheels C of equal size, is to make one revolution in the same sense as the wheel For every five revolutions of the driving spindle carrying the sun wheel B. Determine suitable numbers of teeth for all wheel.
Question No. 18: (a) In an epicyclic gear train, an arm carries two gears A and B having 36 and 45 teeth respectively. If the arm rotates at 150 r.p.m in the anticlockwise direction about the centre of the gear A which is fixed, determine the speed of gear B. If the gear A instead of being fixed, makes 300 r.p.m in the clockwise direction, what will be the speed of gear B? (b) Prove that the resultant unbalanced force is minimum when half of the reciprocating masses are balanced by rotating masses.
Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.
Plate gear C of this gear system are carried on the arm A and free to rotated. the pitch circle diameter of the internally toothed ring gear D is to be 214 mm and the module 4 mm. When the ring gear D is stationary, the arm A, which carries three planet wheels C of equal size, is to make one revolution in the same direction as the sun wheel B for every five revolutions of the driving spindle carrying the sunwheel B.Determine suitable number of teeth for all the wheels and the exact diameter of pitch circle of the ring.1.1.Calculate the number of teeth of the ring gear D.(3)1.2.State an equation tha relate the number of teeth of gear D, B and C.(1)1.3.Use the table method to calculate the number of teeth of gear B.(13)1.4.Calculate the number of teeth for gear C.
Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact. answer with clear word please.
Original Question: The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B QUESTION THAT NEEDS TO BE ANSWERED: For the bevel gear system shown in problem above, determine the angular accelera-tion of gear B when gear A is stationary and member OC has an angular velocityof 10j rad/sec and and angular acceleration of 25j rad/sec2
A gear train as the one shown in problem 1. The gears have the following properties: N2 = 20 teeth and Pd = 10; d3 = 6 in.; d4 = 2 in., and Pd = 8; and N5 = 48 teeth. Determine the velocity of gear 5 as gear 2 drives at 1800 rpm counterclockwise
c) Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact.
A three-stage automobile transmission is shown schematically. The number 6 crankshaft has an angular angle of 50 rad / s.Find the angular velocity (w1) of the drive shaft no. 1 as it rotates with speed [w6 = 50 rad / s]. Each of the spur gears has a fixedrotates around the axis. It should be noted that gears 6 and 5, 4 and 3, 2 and 1 engage each other.. Division Circle of Gearsdiameters d6 = 180mm; d5 = 60mm; d4 = 60mm; d3 = 100mm; d2 = 140mm and d1 = 120mm.
A pinion having 30 teeth, a module of 2 mm, and rotating at 2000 rpm is to drive a gear rotating at 500 rpm.a) Determine the diametral pitch,b) Number of teeth in the gear, and the center distance.