In an epicyclic gear of the sun and planet' type has a fixed outer wheel A, sun wheel S driven. The number of teeth on each planet wheel is 27 and, on the sun wheel is 18 teeth. rotates at a speed of 600 r.p.m. and the spider C carries three planets wheel, which are to be Find the required number of the teeth on the annules wheel and the speed of the planet wheel. A P

In an epicyclic gear of the sun and planet' type has a fixed outer wheel A, sun wheel S driven. The number of teeth on each planet wheel is 27 and, on the sun wheel is 18 teeth. rotates at a speed of 600 r.p.m. and the spider C carries three planets wheel, which are to be Find the required number of the teeth on the annules wheel and the speed of the planet wheel. A P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pitch circle diameter of the smaller of the two spur wheels which mesh externally and haveinvolute teeth is 100 mm. The number of teeth are 16 and 32. The pressure angle is 20° and theaddendum is 0.32 of the circular pitch. Find the length of the path of contact of the pair of teeth.
c) Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact.
A gear system comprises gear A, which is stationary. The bar A'C' rotates with an angular velocity ω1 of 5 rad/s. What will be the angular velocity of gear C? Diameters of the gears: DA = 600 mmDB = 350 mmDC = 200 mm Note: Solve gears B and C by IC method and by relative velocities method
Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact. answer with clear word please.
Consider the epicyclic gear system. Set up a tabke of wheel speeds for the cases where all the wheels rotate..Consider the same system with the sun wheel S as the input and the annulus A as the output.The diameters of the sun andbplanet wheels are 150mm and 75mm,respectively. I the sun wheel runs clockwise at 1000 rev/min and output to input ratio Na/Ns is -1,determine the speeds of the arm L and the planet wheel P.
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm. The number of teeth for each gear is as follows: NA = 60 Teeth, NB = 84 Teeth, NC = 36 Teeth and ND = 60 Teeth.Calculate the output angular velocity at Gear D (ωD).Give your answer in rads-1 to the nearest radian. Gear D is the output gear for the simple gear train shown below.
A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate The maximum length of a path of the approach in mm.
In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?
Q) Two mating gears have 20 and 40 involute teeth of module 10 mm and 20° pressure angle. If the addendum on each wheel is such that the path of contact is maximum and interference are just avoided, find the addendum of the wheel?
The motion transmitted between the teeth of gears in mesh is *
A two-start worm gear that is rotating at 800 rpm drives a 26-tooth worm gear. The worm gear has a pitch diameter of [46] mm and a pitch of [14] mm. If coefficient offriction (u) is 0.06, (i) Determine the helix angle of worm gear. (ii) Determine the speed of gear. (iii) Compute the distance of gear. (iv) Identify the maximum gear efficiency of this transmission system