Two long and four half as long light rods are hinged at their ends to form a pantograph consisting of two identical rhombi. The pantograph is suspended from the ceiling, the lowest hinge of the pantograph is connected to the hinge above it by a light inextensible cord and a load of quenonded from the lowest hinge as shown in the figure, Find

Two long and four half as long light rods are hinged at their ends to form a pantograph consisting of two identical rhombi. The pantograph is suspended from the ceiling, the lowest hinge of the pantograph is connected to the hinge above it by a light inextensible cord and a load of quenonded from the lowest hinge as shown in the figure, Find

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar AB in figure "a" has weight W, length L, and is articulated at point B. End A is supported by a light thread, which passes through a smooth pulley, from which a block hangs at its other end. . Required: (a) Determine how much the block must weigh so that bar AB is in equilibrium. (b) Assuming that the block actually has the value calculated before, but instead of the bar being hinged at B, it only rests on a rough plane with coefficient μ= 0.7, as shown in figure "b". Is the bar balanced?
The rigid arm of negligible weight shown in the figure supports a load of F= 819 N. The chains are fixed to the wall at points D and E and the support A is ball-and-socket (spherical). Find the magnitude of the force FBE
Please show complete solution with formula and free body diagramA rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
For the suspended load F = 637lb in the figure. Find the magnitude of the reaction of the patella at O.
A load of P = 93 kN is supported by a structure consisting of rigid bar ABC, two identical solid bronze (E = 103 GPa) rods, and a solid steel (E = 238 GPa) rod, as shown. The bronze rods (1) each have a diameter of 15 mm and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 28 mm. All bars are unstressed before the load P is applied; however, there is a 2.3-mm clearance in the bolted connection at B. Assume L1 = 2.9 m and L2 = 1.3 m. Determine the downward deflection ν of rigid bar ABC. Express your answer in mm rounded to the nearest hundredths.
The structure shown in Fig. (a) is supported by ball-and-socket joints at O and D, and by a slider bearing at C. The two members OABC and AD, connected by a ball-and-socket joint at A, each weigh 20 N/m. (1) Draw the FBD for the entire structure, and count the unknowns. (2) Draw the FBD for each of the members, and count the total number of unknowns.
Figure 1 below shows the bronze and galvani pipes are fastened to rigid supports at ends A and B and to a rigid plate C at their junction. The bronze pipe is twice as long as the galvani pipe. Two equal and symmetrically placed loads P act on the plate at C.
For the antenna tower shown, it is supported in its upright position by four high tensile wires. Given specifications of the tensile wire: E = 200 GPa, diameter = 12 mm. If a = 6 m and b = 8 m How far(horizontally in mm) would the tip of the tower move from its original position if P = 8 kN.
A load of 6kN is supported as shown in the figure. The weight of the pulley is 2kN. Neglect the weight of the bars. Support A and B are hinge connections. gives the reaction at D.
Please show the formula used and free body diagram A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A horizontal L=1.2 m long mb=14 kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 23° angle with horizontal. A 24 kg store sign is suspended below the bar at d=0.18 m from the right end. Find the magnitude of horizontal hinge force.
The structure shown below consists of an arch AB and an elastic column BC. (Note: Joints where members meet can be treated as pin). Calculate the weight, W, that causes the column to buckle. Determine the support reactions corresponding to the weight from the previous question. Given:a = 3.430 m